HP Z200 HP Z200 SFF Workstation Maintenance and Service Guide - Page 127

Inserting the expansion card

Page 127 highlights

4. Remove the expansion card slot cover by pulling it up, out of the chassis. TIP: Grasp the slot cover between two fingers-one from the inside of the chassis, and one from the outside. Figure 5-53 Removing the slot cover 5. Angle the expansion card to Insert it into the expansion card guide. 6. Align the PCIe card keyway with the slot key, and then firmly seat the card in the slot as shown next. Figure 5-54 Inserting the expansion card 7. Close the expansion card retention clamp by rotating it downward. ● If the PCI retention clamp does not close, ensure that all cards are properly seated, and then try again. ● If required by the card, connect the auxiliary power cable to the card (not illustrated). ENWW Removing and installing components 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199

4.
Remove the expansion card slot cover by pulling it up, out of the chassis.
TIP:
Grasp the slot cover between two fingers—one from the inside of the chassis, and one from
the outside.
Figure 5-53
Removing the slot cover
5.
Angle the expansion card to Insert it into the expansion card guide.
6.
Align the PCIe card keyway with the slot key, and then firmly seat the card in the slot as shown
next.
Figure 5-54
Inserting the expansion card
7.
Close the expansion card retention clamp by rotating it downward.
If the PCI retention clamp does not close, ensure that all cards are properly seated, and then
try again.
If required by the card, connect the auxiliary power cable to the card (not illustrated).
ENWW
Removing and installing components
115