HP Z200 HP Z200 SFF Workstation Maintenance and Service Guide - Page 83

Access panel, Removing the access panel

Get HP Z200 - Small Form Factor Workstation PDF manuals and user guides View all HP Z200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Access panel Before accessing the internal components of the computer, you must remove the access panel. This section describes how to remove and install the access panel. Removing the access panel WARNING! Power off the computer and disconnect the power cord from the electrical outlet before you remove the computer access panel. To remove the access panel: 1. Prepare the computer for servicing by following the Predisassembly procedures on page 68. CAUTION: Failure to follow the predisassembly procedures can result in equipment damage or data loss. 2. Remove locks that are present such as a cable lock. 3. Pull up on the handle (1) and then rotate the panel away from the chassis (2), as shown in the following figure. Figure 5-3 Removing the access panel Installing the access panel To install the access panel: 1. Align the front edge of the access panel with the slot on the front of the chassis. 2. Rotate the back of the panel down onto the chassis, then press firmly until the latch engages. ENWW Removing and installing components 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
Access panel
Before accessing the internal components of the computer, you must remove the access panel.
This section describes how to remove and install the access panel.
Removing the access panel
WARNING!
Power off the computer and disconnect the power cord from the electrical outlet before
you remove the computer access panel.
To remove the access panel:
1.
Prepare the computer for servicing by following the
Predisassembly procedures
on page
68
.
CAUTION:
Failure to follow the predisassembly procedures can result in equipment damage or
data loss.
2.
Remove locks that are present such as a cable lock.
3.
Pull up on the handle (1) and then rotate the panel away from the chassis (2), as shown in the
following figure.
Figure 5-3
Removing the access panel
Installing the access panel
To install the access panel:
1.
Align the front edge of the access panel with the slot on the front of the chassis.
2.
Rotate the back of the panel down onto the chassis, then press firmly until the latch engages.
ENWW
Removing and installing components
71