Netgear FS752TPS FS752TS Setup Manual - Page 17

Network without a DHCP Server, Manually Assigning Network Parameters - default ip

Get Netgear FS752TPS - ProSafe Smart Switch PDF manuals and user guides View all Netgear FS752TPS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

FS700TS Smart Switch Software Administration Manual 8. Use your web browser to manage your switch. The default password is password. Then use this screen to proceed to management of the switch covered in Chapter 2, "Introduction to the Web Browser Interface". Network without a DHCP Server This section describes how to set up your switch in a network without a DHCP server, and is divided into the following tasks: • Manually assign network parameters for your switch • Configure the NIC settings on the host PC • Log in to the web-based switch management utility Manually Assigning Network Parameters If your network has no DHCP service, you must assign a static IP address to your switch. You can also assign the switch a static IP address even if your network has DHCP service. Proceed as follows: 1. Connect the FS700TS 10/100 Stackable Smart Switch with Gigabit Ports to your existing network. 2. Power on the switch by plugging in the AC-DC power adapter. The default IP is 192.168.0.239. 3. Install the SmartWizard Discovery utility on your computer. The SmartWizard Discovery utility is located on the switch installation CD. 4. Start the SmartWizard Discovery utility. 5. Click Discover for the SmartWizard Discovery utility to find your FS700TS 10/100 Stackable Smart Switch with Gigabit Ports. You should see a screen similar to that shown in Figure 1-1. 6. Click Configuration Setting. A screen similar to that shown below appears. Getting Started with Switch Management 1-5 v1.0, September 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
FS700TS Smart Switch Software Administration Manual
Getting Started with Switch Management
1-5
v1.0, September 2007
8.
Use your web browser to manage your switch. The default password is
password
. Then use
this screen to proceed to management of the switch covered in
Chapter 2, “Introduction to the
Web Browser Interface”
.
Network without a DHCP Server
This section describes how to set up your switch in a network without a DHCP server, and is
divided into the following tasks:
•
Manually assign network parameters for your switch
•
Configure the NIC settings on the host PC
•
Log in to the web-based switch management utility
Manually Assigning Network Parameters
If your network has no DHCP service, you must assign a static IP address to your switch. You can
also assign the switch a static IP address even if your network has DHCP service. Proceed as
follows:
1.
Connect the FS700TS 10/100 Stackable Smart Switch with Gigabit Ports to your existing
network.
2.
Power on the switch by plugging in the AC-DC power adapter. The default IP is
192.168.0.239.
3.
Install the SmartWizard Discovery utility on your computer. The SmartWizard Discovery
utility is located on the switch installation CD.
4.
Start the SmartWizard Discovery utility.
5.
Click
Discover
for the SmartWizard Discovery utility to find your FS700TS 10/100 Stackable
Smart Switch with Gigabit Ports. You should see a screen similar to that shown in Figure 1-1.
6.
Click
Configuration Setting
. A screen similar to that shown below appears.