Netgear FS752TPS FS752TS Setup Manual - Page 9

About This Manual, Who Should Use this Book - documentation

Get Netgear FS752TPS - ProSafe Smart Switch PDF manuals and user guides View all Netgear FS752TPS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

About This Manual The NETGEAR® FS700TS Smart Switch Software Administration Manual describes how to install, configure, operate, and troubleshoot the FS700TS 10/100 Stackable Smart Switch with Gigabit Ports using, its included software. This book describes the software configuration procedures and explains the options available within those procedures. Who Should Use this Book The information in this manual is intended for readers with intermediate to advanced system management skills. This document was created primarily for the system administrator who wishes to install and configure the FS700TS Smart Switch in a network. This user guide assumes that the reader has a general understanding of switch platforms and a basic knowledge of Ethernet and networking concepts. To install this switch, it is not necessary to understand and use all of its capabilities. Once basic configuration is performed, the switch operates using the remaining factory default parameters. However, a greater level of configuration-anywhere from the basic up to the maximum possible-will allow your network the full benefit of the switch's features. The web interface simplifies this configuration at all levels. How to Use This Book This document describes configuration commands for the FS700TS Smart Switch software. The commands can all be accessed from the Web interface. • Chapter 1, "Getting Started with Switch Management" describes how to use the SmartWizard Discovery utility to set up your switch so that you can communicate with it. • Chapter 2, "Introduction to the Web Browser Interface" introduces the Web browser interface. • Chapter 3, "Managing System Settings" describes how to configure the System functions. • Chapter 4, "Configuring Switching Settings" describes how to configure the Switching functions. • Chapter 5, "Configuring QoS" describes how to configure QoS functions. ix v1.0, September 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
ix
v1.0, September 2007
About This Manual
The
NETGEAR
®
FS700TS Smart Switch Software Administration Manual
describes how to
install, configure, operate, and troubleshoot the FS700TS 10/100 Stackable Smart Switch with
Gigabit Ports using, its included software. This book describes the software configuration
procedures and explains the options available within those procedures.
Who Should Use this Book
The information in this manual is intended for readers with intermediate to advanced system
management skills.
This document was created primarily for the system administrator who wishes to install and
configure the FS700TS Smart Switch in a network. This user guide assumes that the reader has a
general understanding of switch platforms and a basic knowledge of Ethernet and networking
concepts. To install this switch, it is not necessary to understand and use all of its capabilities.
Once basic configuration is performed, the switch operates using the remaining factory default
parameters. However, a greater level of configuration—anywhere from the basic up to the
maximum possible—will allow your network the full benefit of the switch’s features. The web
interface simplifies this configuration at all levels.
How to Use This Book
This document describes configuration commands for the FS700TS Smart Switch software. The
commands can all be accessed from the Web interface.
•
Chapter 1, “Getting Started with Switch Management”
describes how to use the SmartWizard
Discovery utility to set up your switch so that you can communicate with it.
•
Chapter 2, “Introduction to the Web Browser Interface”
introduces the Web browser interface.
•
Chapter 3, “Managing System Settings”
describes how to configure the System functions.
•
Chapter 4, “Configuring Switching Settings”
describes how to configure the Switching
functions.
•
Chapter 5, “Configuring QoS”
describes how to configure QoS functions.