Home » Netgear Manuals » Hubs & Switches » Netgear FS752TPS » Manual Viewer

Netgear FS752TPS FS752TS Setup Manual - Page 79

Duplex Mode, Auto Negotiation, Back Pressure, Flow Control, MDI/MDIX

Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

FS700TS Smart Switch Software Administration Manual - 10M - The port is currently operating at 10 Mbps. - 100M - The port is currently operating at 100 Mbps. - 1000M - The port is currently operating at 1000 Mbps. • Duplex Mode - Select the port duplex mode. This field is configurable only when auto negotiation is disabled and the port speed is set to 10M or 100M. The possible field values are: - Full - The interface supports transmission between the device and its link partner in both directions simultaneously. - Half - The interface supports transmission between the device and the client in only one direction at a time. - Auto - The interface supports transmission between the device and the link partner based on the transmission mode of the link partner. • Auto Negotiation - Select the port auto negotiation status. Auto negotiation is a protocol between two link partners that enables a port to advertise its transmission rate, duplex mode, and flow control abilities to its partner. The possible field values are: - Enable - Auto negotiation is enabled. - Disable - Auto negotiation is disabled. • Back Pressure - Select the back pressure mode of the Port. Back Pressure mode is used with half duplex mode to disable ports from receiving messages. Back Pressure mode is disabled by default. The possible field values are: - Enable - Back pressure mode is enabled. - Disable - Back pressure mode is disabled. • Flow Control - Select the flow control status of the port. Operates when the port is in full duplex mode. Flow control is disabled by default. The possible field values are: - Enable - Flow control is enabled. - Disable - Flow control is disabled. • MDI/MDIX - Select the MDI/MDIX status of the port. Hubs and switches are deliberately wired opposite the way end stations are wired, so that when a hub or switch is connected to an end station, a straight through Ethernet cable can be used and the pairs will match up properly. When two hubs or switches are connected to each other or two end stations are connected to each other, a crossover cable is used to ensure that the correct pairs are connected. The possible field values are: Configuring Switching Settings 4-3 v1.0, September 2007

Section	Page
FS700TS Smart Switch Software Administration Manual	1
Contents	5
About This Manual	9
Who Should Use this Book	9
How to Use This Book	9
Conventions, Formats, and Scope	10
How to Use This Manual	11
How to Print this Manual	12
Revision History	12
Chapter 1 Getting Started with Switch Management	13
System Requirements	13
Switch Management Interface	14
Network with a DHCP Server	15
Network without a DHCP Server	17
Manually Assigning Network Parameters	17
NIC Setting on the Host that Accesses the FS700TS 10/100 Stackable Smart Switch with Gigabit Ports	18
Web Access	19
Additional Utilities	20
Password Change	21
Firmware Upgrade	21
Exit	22
Chapter 2 Introduction to the Web Browser Interface	23
Logging Into the NETGEAR Home Screen	23
The Navigation Menu	24
Using the NETGEAR Web Management System Options	25
Device Management Buttons	25
Informational Services	26
Help Navigation Tab	26
Accessing Device Information	26
Using Screen and Table Options	27
Selecting an Entry	28
Adding an Entry	28
Modifying an Entry	29
Deleting an Entry	29
Special Table Options	30
Gold Buttons	30
Quick Boxes	30
Interface View and Selection	32
Chapter 3 Managing System Settings	35
Using the System Settings Utility	35
Management	35
System Information	35
IP Configuration	37
Time	39
Time Configuration	39
SNTP Server Configuration	40
Device View	41
Stacking	41
Operation Modes	42
Understanding Stack Topology	43
Stacking Ports	43
Stacking Members and Unit ID	44
Removing and Replacing Stacking Members	44
Inserting a Stacking Member	46
Exchanging Stacking Members	46
Switching the Stacking Master	46
Stack Configuration and Management	46
Basic	46
Stack Configuration	47
Advanced	48
Stack Configuration	48
Stack Management	49
PoE	50
Basic	51
PoE Configuration	51
Advanced	52
PoE Configuration	52
PoE Port Configuration	53
SNMP	56
SNMPv1/v2	56
Community Configuration	57
Trap Configuration	58
SNMPv3	60
Engine ID	61
View Name	62
View Content	63
Community Configuration	64
Group Configuration	66
User Configuration	68
Global Trap Configuration	70
Trap Configuration	71
Trap Filter Name	73
Trap Filter Content	74
Chapter 4 Configuring Switching Settings	77
Configuring Switching Settings	77
Ports	77
Port Configuration	77
LAG	80
Basic	81
LAG Configuration	81
LAG Membership	83
Advanced	84
LAG Configuration	84
LAG Membership	87
LACP	88
LACP Port Priority	89
VLAN	90
Basic	90
VLAN Configuration	90
Advanced	92
VLAN Configuration	92
VLAN Membership	93
Port PVID Configuration	96
STP	97
Basic	98
STP Configuration	98
Advanced	99
STP Configuration	99
CST Configuration	101
CST Port Configuration	103
Multicast	105
Basic	105
IGMP Snooping Configuration	105
Advanced	107
IGMP Snooping Configuration	107
Multicast Group Configuration	109
Multicast Group Membership	110
Multicast Forward All	111
Address Table	112
Basic	113
Address Table	113
Advanced	114
Static Addresses	114
Dynamic Addresses	115
Address Table	116
Chapter 5 Configuring QoS	119
Configuring the Basic and Advanced QoS Settings	119
CoS	119
Basic	120
CoS Global Configuration	120
CoS Interface Configuration	121
Queue	122
Bandwidth	123
Advanced	124
CoS to Queue Mapping	124
DSCP to Queue Mapping	125
Chapter 6 Managing Security	129
Setting Security Configuration Options	129
Management Security	129
User Configuration	129
Change Password	130
RADIUS	130
TACACS+	132
Authentication List	134
Port Authentication	135
Basic	136
802.1X Configuration	136
Advanced	137
802.1X Configuration	137
Port Authentication	139
Traffic Control	141
Storm Control	141
Port Security	143
ACL	145
Basic	145
MAC ACL	145
MAC Rules	147
MAC Binding Configuration	148
Binding Table	149
Chapter 7 Monitoring the Switch	151
Setting Monitoring Options	151
Logs	151
Logs Configuration	152
Log Filter	153
Memory Log	154
Flash Log	155
Server Log	157
RMON	159
Basic	159
Statistics	159
Advanced	160
Statistics	160
History Control	163
History Table	165
Events Control	166
Events Log	168
Alarms	169
Port Mirroring	171
Port Mirroring	172
Chapter 8 Maintenance	175
Using the Maintenance Options	175
Reset	175
Device Reboot	175
Factory Default	176
Upload	177
Upload	177
Download	178
Download	178
File Management	180
Active Image	180
Troubleshooting	181
Diagnostics	181
Cable Test	181
Chapter 9 Online Help	183
Online Help	183
Support	183
User Guide	184
Appendix A Default Settings	185

Match case Limit results 1 per page

FS700TS Smart Switch Software Administration Manual

Configuring Switching Settings

4-3

v1.0, September 2007

–

10M – The port is currently operating at 10 Mbps.

–

100M – The port is currently operating at 100 Mbps.

–

1000M – The port is currently operating at 1000 Mbps.

•

Duplex Mode

– Select the port duplex mode. This field is configurable only when auto

negotiation is disabled and the port speed is set to 10M or 100M. The possible field values

are:

–

Full – The interface supports transmission between the device and its link partner in

both directions simultaneously.

–

Half – The interface supports transmission between the device and the client in only

one direction at a time.

–

Auto – The interface supports transmission between the device and the link partner

based on the transmission mode of the link partner.

•

Auto Negotiation

– Select the port auto negotiation status. Auto negotiation is a protocol

between two link partners that enables a port to advertise its transmission rate, duplex

mode, and flow control abilities to its partner. The possible field values are:

–

Enable – Auto negotiation is enabled.

–

Disable – Auto negotiation is disabled.

•

Back Pressure

– Select the back pressure mode of the Port. Back Pressure mode is used

with half duplex mode to disable ports from receiving messages. Back Pressure mode is

disabled by default. The possible field values are:

–

Enable – Back pressure mode is enabled.

–

Disable – Back pressure mode is disabled.

•

Flow Control

– Select the flow control status of the port. Operates when the port is in full

duplex mode. Flow control is disabled by default. The possible field values are:

–

Enable – Flow control is enabled.

–

Disable – Flow control is disabled.

•

MDI/MDIX

– Select the MDI/MDIX status of the port. Hubs and switches are

deliberately wired opposite the way end stations are wired, so that when a hub or switch is

connected to an end station, a straight through Ethernet cable can be used and the pairs

will match up properly. When two hubs or switches are connected to each other or two end

stations are connected to each other, a crossover cable is used to ensure that the correct

pairs are connected. The possible field values are: