Yamaha MO6 Owner's Manual - Page 187

Voice mode Song Job mode NumberOfTimes 06: Thin Out TR (Track) 001 : 1 : 000 - 999 : 4 : 479 EventType 07: Modify Control Data TR (Track) 001 : 1 : 000 - 999 : 4 : 479 EventType SetAll Rate Offset 08: Beat Stretch TR (Track) 001 : 1 : 000 - 999 : 4 : 479 Rate [F4] MEAS (Measure Job) 01: Create Measure Determines the number of times the data creation is to be repeated. For example, if data is created in the range M001:1:000 - M003:1:000 and this parameter is set to 03, the same data will be created at M003:1:000 - M005:1:000 and M005:1:000 - M007:1:000. This Job lets you insert continuous volume or filter cutoff variations to create tremolo or wah effects. Settings: 01 - 99 This Job thins out the specified type of continuous data in the specified range-allowing you to free up memory space for other data or further recording. Determines the track (01 - 16, TMP, all) and range of measures/beats/clocks over which the Job is applied. Determines the event type to be thinned. Settings: PB (Pitch Bend), CC (Control Change)*, CAT (Channel Aftertouch), PAT (Polyphonic Aftertouch), TMP (Tempo) * You can also specify the CC No. (Control Change number). n The Thin Out Job will not work on continuous data that has a clock interval of greater than 60 clocks per event. This Job lets you change the values of a specified type of control change data-pitch bend, control change, aftertouch, etc.-in the specified range. Data changes are calculated as follows: Modified value = (original value x Rate) + Offset. The modified value cannot exceed the minimum/maximum limits of the parameter. Any result lower than the minimum is set to the minimum; any result higher than the maximum is set to the maximum. Determines the track (01 - 16, TMP, all) and range of measures/beats/clocks over which the Job is applied. Determines the event type to be modified. Settings: PB (Pitch Bend), CC (Control Change)*, CAT (Channel Aftertouch), PAT (Polyphonic Aftertouch), TMP (Tempo) * You can also specify the CC No. (Control Change number). Sets all target events to the same fixed value. When set to "off," the Set All parameter has no effect. When set to a value other than "off," the Rate and Offset parameters are unavailable and appear as "***" on the display. Settings: off, 000 -127 (-8192 - +8191 for pitch bend, 0.1 - 300.0 for tempo) Determines the percentage by which the target events will be shifted from their original values. When the Set All parameter (above) is set to something other than "off," this parameter appears as "***" and cannot be changed. Settings: 000% - 200%, *** Adds a fixed value to the Rate-adjusted event values. When the Set All parameter (above) is set to something other than "off," this parameter appears as "***" and cannot be changed. Settings: -127 - 127 (-8192 - +8191 for pitch bend, -275 - +275 for tempo), *** This Job performs time-expansion or compression over the selected range. Keep in mind that this operation affects all event timing, note step times, and note gate times. Determines the track (01 - 16, all) and range of measures/beats/clocks over which the Job is applied. Determines the amount of time expansion or compression as a percentage. Settings higher than 100% produce expansion, and settings below 100% produce compression. Settings: 025%-400% This Job creates empty measures at the specified location in all tracks. Meter (time signature) of Number of measures measures to be inserted to be inserted Source data 001 - 004 005 - 016 8 measures inserted at measure 5 001 - 004 005 - 012 013 - 024 Insertion point (measure number) The inserted 8 measures Meter of measures to be inserted Determines the meter or time signature of the measures to be created. You may find it convenient to use this parameter when you need to create a Song that incorporates meter changes. Settings: 1/16 - 16/16, 1/8 - 16/8, 1/4 - 8/4 Insertion point (Measure number) Determines the insert point (measure number) at which the newly created blank measures will be inserted. Settings: 001 - 999 Number of measures to be inserted Determines the number of empty measures to be created and inserted. Settings: 01 - 99 n When empty measures are inserted, measure and meter data following the insert point are moved forward accordingly. n If the insert point is set after the last measure containing data, only the meter data at that point is set without actually inserting the measures. Performance mode Song mode Pattern mode Reference Mixing Voice mode Utility mode Master mode File mode Owner's Manual 187