HP Z210 HP Z210 CMT Workstation Maintenance and Service Guide - Page 103

retention clamp 1 as shown below.

Get HP Z210 PDF manuals and user guides View all HP Z210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

3. Remove the expansion card retainer (if installed): grasp the top of the clamp (1), squeeze the release handles until the bottom of the clamp releases from the clamp rail (2) (it should click when it releases), and swing the clamp out from the back panel (3). Figure 5-29 Removing expansion card retainer 4. Remove all cables connected to the expansion card. 5. Push down on the expansion card retention clamp levers on the inside of the chassis to open the retention clamp (1) as shown below. Figure 5-30 Removing the expansion card 6. If the card is in one of the slots with a latch, release the latch (2). (Note that there are two different styles of latch.) ENWW Removing and installing components 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
3.
Remove the expansion card retainer (if installed): grasp the top of the clamp (1), squeeze the
release handles until the bottom of the clamp releases from the clamp rail (2) (it should click when
it releases), and swing the clamp out from the back panel (3).
Figure 5-29
Removing expansion card retainer
4.
Remove all cables connected to the expansion card.
5.
Push down on the expansion card retention clamp levers on the inside of the chassis to open the
retention clamp (1) as shown below.
Figure 5-30
Removing the expansion card
6.
If the card is in one of the slots with a latch, release the latch (2). (Note that there are two different
styles of latch.)
ENWW
Removing and installing components
91