HP Z210 HP Z210 CMT Workstation Maintenance and Service Guide - Page 92

Power supply, Removing the power supply

Get HP Z210 PDF manuals and user guides View all HP Z210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Power supply This section describes how to remove and install a power supply. Removing the power supply To remove the power supply: 1. Disconnect power from the workstation (see Predisassembly procedures on page 62). 2. Remove the side access panel (see Removing the side access panel on page 65). 3. Disconnect all of the power supply cables from the system board and all peripheral devices (hard drives, optical drives, and others as needed). 4. Remove the four screws from the rear of the chassis (1). 5. Slide the power supply inward then up to remove it from the chassis (2). Figure 5-21 Removing power supply Installing the power supply To install the power supply, reverse the previous steps. 80 Chapter 5 Replacing components ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
Power supply
This section describes how to remove and install a power supply.
Removing the power supply
To remove the power supply:
1.
Disconnect power from the workstation (see
Predisassembly procedures
on page
62
).
2.
Remove the side access panel (see
Removing the side access panel
on page
65
).
3.
Disconnect all of the power supply cables from the system board and all peripheral devices (hard
drives, optical drives, and others as needed).
4.
Remove the four screws from the rear of the chassis (1).
5.
Slide the power supply inward then up to remove it from the chassis (2).
Figure 5-21
Removing power supply
Installing the power supply
To install the power supply, reverse the previous steps.
80
Chapter 5
Replacing components
ENWW