HP Z210 HP Z210 CMT Workstation Maintenance and Service Guide - Page 155

Screen message, Probable cause, Recommended action, Run the Computer Setup F10 Utility.

Get HP Z210 PDF manuals and user guides View all HP Z210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 155 highlights

Table 6-9 POST error messages (continued) Screen message Probable cause Recommended action 513-Front Chassis fan not detected Front fan missing, disconnected, or defective. 1. Reseat the fan cable. 2. Reseat the fan. 3. Replace the fan. 514-Memory fan not detected Memory fan missing, disconnected, or 1. Reseat the fan cable. defective. 2. Reseat the fan. 3. Replace the fan. 515-CPU Overtemp occurred Insufficient processor cooling or processor defect. 1. If necessary, add a heatsink to the processor and ensure proper operation. 2. Replace the processor. 516-Chipset fan not detected Chipset fan missing, disconnected, or defective. 1. Reseat the fan cable. 2. Reseat the fan. 3. Replace the fan. 517-Low power CPU heatsink(s) detected for high power CPUs Inadequate heatsink is installed. Replace the low power heatsink with a high power heatsink. 518-Power supply wattage insufficient for hardware configuration Computer configuration requires more 1. Reduce the computer power consumption. power than the power supply can provide. 2. Replace the power supply with a high output power supply. 601-Diskette Controller Error Diskette controller circuitry or diskette drive circuitry incorrect. 1. Run the Computer Setup (F10) utility. 2. Verify cabling and replace defective cables if necessary. 3. Clear CMOS. 4. Replace the diskette drive. 5. Replace the system board. 605-Diskette Drive Type Error Mismatch in drive type. 1. Run the Computer Setup (F10) Utility. 2. Disconnect any other diskette controller devices (tape drives). 3. Clear the CMOS. 610-External Storage Device Failure External storage device is not detected, is improperly connected, or is defective. 1. Verify that the external device is present and connected properly. 2. Replace the external device. 611-Primary Floppy Port Address Assignment Conflict The flexible disk drive is configured at Select a new address for the flexible disk drive. a previously assigned address. 912-Computer Cover Has Been Removed Since Last System Start Up N/A No action required. ENWW Diagnostic codes and errors 143

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
Table 6-9
POST error messages
(continued)
Screen message
Probable cause
Recommended action
513—Front Chassis fan not
detected
Front fan missing, disconnected, or
defective.
1.
Reseat the fan cable.
2.
Reseat the fan.
3.
Replace the fan.
514—Memory fan not
detected
Memory fan missing, disconnected, or
defective.
1.
Reseat the fan cable.
2.
Reseat the fan.
3.
Replace the fan.
515—CPU Overtemp
occurred
Insufficient processor cooling or
processor defect.
1.
If necessary, add a heatsink to the processor and
ensure proper operation.
2.
Replace the processor.
516—Chipset fan not detected
Chipset fan missing, disconnected, or
defective.
1.
Reseat the fan cable.
2.
Reseat the fan.
3.
Replace the fan.
517—Low power CPU
heatsink(s) detected for high
power CPUs
Inadequate heatsink is installed.
Replace the low power heatsink with a high power
heatsink.
518—Power supply wattage
insufficient for hardware
configuration
Computer configuration requires more
power than the power supply can
provide.
1.
Reduce the computer power consumption.
2.
Replace the power supply with a high output
power supply.
601—Diskette Controller Error
Diskette controller circuitry or diskette
drive circuitry incorrect.
1.
Run the Computer Setup (F10) utility.
2.
Verify cabling and replace defective cables if
necessary.
3.
Clear CMOS.
4.
Replace the diskette drive.
5.
Replace the system board.
605—Diskette Drive Type
Error
Mismatch in drive type.
1.
Run the Computer Setup (F10) Utility.
2.
Disconnect any other diskette controller devices
(tape drives).
3.
Clear the CMOS.
610—External Storage Device
Failure
External storage device is not
detected, is improperly connected, or
is defective.
1.
Verify that the external device is present and
connected properly.
2.
Replace the external device.
611—Primary Floppy Port
Address Assignment Conflict
The flexible disk drive is configured at
a previously assigned address.
Select a new address for the flexible disk drive.
912—Computer Cover Has
Been Removed Since Last
System Start Up
N/A
No action required.
ENWW
Diagnostic codes and errors
143