Yamaha M7CL M7cl V1 Owner's Manual - Page 143

C TALKBACK DIMMER field Here you can view and make settings for the Talkback Dimmer. • TALKBACK DIMMER knob ...........This adjusts the amount by which the monitor signal will be attenuated when talkback is on. You can use multifunction encoder 5 to control this. This operation can also be performed in the TALKBACK DIMMER field of the MONITOR screen. • TALKBACK DIMMER indicator ...........This indicator shows that talkback is on, and that the talkback dimmer is operating. HINT • If the normal dimmer and the talkback are both switched on simultaneously, the setting with the greatest amount of attenuation will be applied. D MONITOR DELAY field This field specifies the monitor delay setting by which the monitor signal is delayed. You can use this in large auditoriums where there is a time difference between the monitor signal and the direct sound. • MONITOR DELAY knob ...........Adjusts the delay time for the monitor signal. You can use multifunction encoder 6 to control this. • MONITOR DELAY ON button ...........If this button is on, the monitor signal will be delayed according to the setting of the MONITOR DELAY knob. E MONO MONITOR button This button allows monaural monitoring. If this button is on, the signal sent from the PHONES OUT jack and the MONITOR OUT L/R channels will be monaural. F PHONES LEVEL LINK button If this is on, the MONITOR LEVEL knob will adjust the level of the signal sent to the PHONES OUT jack. G OUTPUT button Switches the monitor function on/off. This operation can also be performed using the OUTPUT button in the MONITOR screen. H Meter field • Output select button ...........This opens the OUTPUT PORT SELECT popup window, where you can select the port that will output the monitor signal. • Level meter ....This indicates the level of the monitor signal. This meter shows the level immediately before the dimmer. I ASSIGN field If you selected DEFINE in the SOURCE SELECT field, use this field to specify the monitor source. You can select up to eight monitor sources simultaneously. Pressing the CLEAR ALL button will clear all selections. Using the Monitor function 4 Use the buttons of the SOURCE SELECT field to select a monitor source. In the SOURCE SELECT field you can select only one monitor source. However if you've selected DEFINE, you can use the ASSIGN field to specify multiple monitor sources. The following table shows the monitor sources you can select in the SOURCE SELECT field. STEREO L/R button MONO (C) button LCR button ST IN 1-4 buttons DEFINE button STEREO L/R channel output signal MONO channel output signal STEREO L/R + MONO channel (LCR) output signal ST IN jacks 1-4 input signals The signal(s) selected in the ASSIGN field If you've selected DEFINE in the SOURCE SELECT field, you can use the ASSIGN field to select multiple sources. The following table shows the monitor sources you can select in the ASSIGN field. MIX 1-16 buttons MTRX 1-8 buttons STEREO L/R button MONO (C) button ST IN 1-4 buttons Output signals of MIX channels 1-16 Output signals of MATRIX channels 1-8 STEREO L/R channel output signal MONO channel output signal ST IN jacks 1-4 input signals NOTE • You can select a maximum of eight monitor sources in the ASSIGN field. If you select eight monitor sources, no further selections will be possible. Please turn off the buttons for unneeded sources. 5 To specify a port as the output destination for monitor signals L, C, R, press one of the output select buttons (L/R/C) in the meter field to open the OUTPUT PORT SELECT popup window, and choose from the following monitor signal output destinations (multiple selections are allowed). Monitor/Cue 13 OMNI 1-16 2TR OUT L, R SLOT 1-3 OMNI OUT jacks 1-16 2TR OUT DIGITAL jack L, R Output channels 1-16 of an I/O card installed in slots 1-3 When you've selected an output port, press the CLOSE button to close the popup window. In the same way, specify the output ports for MONITOR OUT L, R, and C. M7CL Owner's Manual 143