Yamaha M7CL M7cl V1 Owner's Manual - Page 67
Using the Centralogic Make sure that the TO MATRIX SEND
![]() |
View all Yamaha M7CL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 67 highlights
Sending the signal from an input channel to the MATRIX buses If the send-destination MATRIX bus is assigned as stereo, the left knob of the two adjacent TO MATRIX SEND LEVEL knobs will operate as the TO MATRIX PAN knob (for a ST IN channel, it will operate as the TO MATRIX BALANCE knob). For an INPUT channel, the right knob will adjust the common send level to the two MATRIX buses, and the left knob will adjust the panning between the two MATRIX buses. Turning the left TO MATRIX SEND LEVEL knob toward the left will increase the amount of signal sent to the odd-numbered MATRIX bus, and turning it toward the right will increase the amount sent to the even-numbered MATRIX bus. For a ST IN channel, the right knob adjusts the common send level for the two MATRIX buses, and the left knob adjusts the volume balance of the left and right signals sent to the two MATRIX buses. Turning the left TO MATRIX SEND LEVEL knob toward the left will increase the amount of signal sent from the Lchannel to the odd-numbered MATRIX bus, and turning it toward the right will increase the amount sent from the R-channel to the even-numbered MATRIX bus. HINT • If necessary, the TO MATRIX PAN/TO MATRIX BALANCE knob setting can be linked with operations of the TO ST PAN/ TO ST BALANCE knob shown in the STEREO/MONO field of the OVERVIEW screen (→ p. 212). 5 Make sure that the TO MATRIX SEND ON/ OFF button is turned on for the send-destination MATRIX bus. If this button is off, press the button in the screen to turn it on. 6 In the SELECTED CHANNEL section, use the MATRIX SEND LEVEL knobs to adjust the send levels to the MATRIX buses. HINT • If you want to monitor the signal being sent to a specific MATRIX bus, use the navigation keys to access the corresponding MATRIX channel, and press the appropriate [CUE] key in the Centralogic section. 7 You can use the top panel [SEL] keys to switch input channels and control the send level to the MATRIX buses in the same way. Using the Centralogic section Here's how you can use the multifunction encoders of the Centralogic section to adjust the send level of the signals sent from eight consecutive input channels to a specific MATRIX bus. 1 Make sure that an output port is assigned to each MATRIX bus to which you want to send signals, and that your monitor system or external effect etc. is connected to the corresponding output port. For details on assigning an output port to a MATRIX bus refer to p. 95. For details on connecting an exter- 5 nal device, refer to p. 39. 2 Use the navigation keys to access the OVERVIEW screen that includes the input channel you want to control. In the OVERVIEW screen, you can use the TO MIX/ TO MATRIX field to adjust the send levels to the MIX/MATRIX bus. Input channel operations 1 2 1 TO MIX/TO MATRIX field In this field you can switch the on/off status and adjust the level of the signal sent from the input channel to the MIX buses / MATRIX buses. Use the TO MIX/TO MATRIX buttons of the SELECTED CHANNEL VIEW screen to switch the type of send destination shown in this field (→ p. 82). B TO MATRIX SEND LEVEL knob This screen shows the send level of the signal sent from the input channels to the MATRIX bus. To adjust the send level, press the appropriate knob to select it, and operate multifunction encoders 1-8. If the send-destination MATRIX bus is set to stereo, the left one of the two adjacent knobs will be linked as the TO MATRIX PAN knob. 3 Press the TO MATRIX SEND LEVEL knob for the desired send-destination MATRIX bus. A bold frame will appear around all TO MATRIX SEND LEVEL knobs for that MATRIX bus. M7CL Owner's Manual 67
![](/manual_guide/products/yamaha-m7cl-m7cl-v1-owners-manual-022fa08/67.png)