Yamaha M7CL M7cl V1 Owner's Manual - Page 159

About the virtual rack C MODULE SELECT Use these buttons to select the GEQ or effect that will be mounted in the rack. Each button has the following function. • BLANK button ...........Removes the GEQ or effect currently mounted in the rack; the rack will be empty. • 31 Band GEQ button ...........Mounts a 31 Band GEQ in the rack. • Flex15GEQ button ...........Mounts a Flex15GEQ in the rack. • EFFECT button ...........Mounts an effect in the rack. However, effects cannot be mounted in racks 1-4. HINT • Input/output patching will be defeated when you change the item mounted in a rack. D CANCEL button Cancels the changes you made in the RACK MOUNTER popup window, and closes the window. E OK button Applies the changes you made in the RACK MOUNTER popup window, and closes the window. NOTE • Be aware that if you remove a GEQ or effect that was mounted in a rack and close the window, all parameter settings for that GEQ or effect will be discarded. If you have not yet closed the window, you can recover the parameter settings by mounting the same GEQ or effect once again. HINT • You can also display the RACK MOUNTER popup window by pressing a vacant rack in the GEQ/EFFECT field. 4 Use the MODULE SELECT buttons to select the item you want to mount, and press the OK button. 5 To select the input source for a rack, press the INPUT button for that rack. The OUTPUT CH SELECT popup window will appear, allowing you to select the input source for the rack. Switch the tabs as necessary, and select the input source that you want to use. When you select an input source in the OUTPUT CH SELECT popup window, a dialog box will ask you for confirmation. To confirm the operation, press the OK button. HINT • You have the option of making settings so that the confirmation dialog box does not appear (→ p. 198). • Normally you can specify two channels of input for each rack. However if you have selected 31 Band GEQ, only one channel can be used. 1 2 1 Channel select buttons Use these buttons to select the input source. Use the four tabs to switch between groups of input sources shown in the window. B CLOSE button Closes the popup window. The following input sources can be selected in this popup window. Tab name Button name Input source MIX 1-16 MIX channel 1-16 outputs OUT CH (*1) MATRIX 1-8 MATRIX channel 1-8 outputs STEREO L, STEREO R, MONO (C) STEREO (L/R) channel and MONO (C) channel outputs CH 1-32 (INSERT OUT) CH 1-32 INPUT channel 1-32 Insert Outs CH 33-48 (INSERT OUT) CH 33-48 {M7CL-48 only} INPUT channel 33-48 Insert Outs MIX 1-16 MIX channel 1-16 Insert Outs OUT CH (INSERT OUT) MATRIX 1-8 STEREO L, STEREO R, MONO (C) MATRIX channel 1-8 Insert Outs STEREO (L/R) channel and MONO (C) channel Insert Outs *1 Cannot be selected for 31 Band GEQ or Flex15GEQ. HINT • If you select Insert Out as the input source for 31 Band GEQ or Flex15GEQ, the Insert In of the same channel will automatically be selected as the output destination for that rack. When you defeat an insert-out, the insert-in will be defeated automatically. For details on Insert Out/In, refer to "Inserting an external device into a channel" (→ p. 100). 16 Graphic EQ and effects 6 To select the output source for a rack, press the OUTPUT button for that rack. The INPUT CH SELECT popup window will appear, allowing you to select the output destination for the rack. Switch the tabs as necessary, and select the output destination that you want to use. When you select an output destination in the INPUT CH SELECT popup window, a dialog box will ask you to confirm the change. To confirm the change, press the OK button. M7CL Owner's Manual 159