Yamaha M7CL M7cl V1 Owner's Manual - Page 185

Using program changes to recall scenes and library items 1 PROGRAM CHANGE field Here you can switch program change transmission/ reception on/off, and specify whether program changes will be echoed out. This setting is linked with the PROGRAM CHANGE field of the MIDI SETUP page. B PROGRAM CHANGE MODE field Here you can select the program change transmit/ receive mode. This setting is linked with the PROGRAM CHANGE MODE field of the MIDI SETUP page. C List This list shows the event (scene recall / effect library recall) assigned to each program number. The list shows the following items. • CH/BANK........Indicates the MIDI channel 1-16 on which program changes are transmitted/received. In Single mode if the BANK button is on, this will be labeled BANK, and the numerical value in this column will correspond to the bank number. • NO Indicates the program number 1- 128. • PROGRAM CHANGE EVENT ...........Indicates the type/number/title of the event assigned to the program number for each MIDI channel (bank number). You can press an individual event to access the MIDI PROGRAM CHANGE popup window, where you can change the assignment for each program number. D CLEAR ALL button Pressing this button will delete all event assignments in the list. E INITIALIZE ALL button Pressing this button will restore all event assignments in the list to their default state. F Scroll knob This knob scrolls the contents of the list. You can use multifunction encoder 1 to control this. 6 Use the buttons of the PROGRAM CHANGE MODE field to select the program change transmission/reception mode. You can select one of the following two program change transmission/reception modes. ● Multi mode (when the MULTI button is on) Program changes of all MIDI channels will be transmitted and received. (The transmit/receive channel specified in the MIDI SETUP page will be ignored.) When a program change is received, the event assigned to the corresponding MIDI channel and program number in the list will be executed. When you execute the specified event on the M7CL, the program change of the corresponding MIDI channel and program number in the list will be transmitted. ● Single mode (when the SINGLE button is on) Only program changes of the transmit (Tx) and receive (Rx) channels specified in the MIDI SETUP page will be transmitted and received. When a program change on the Rx channel is received, the event assigned to that program number of the corresponding channel in the list will be executed. When you execute the specified event on the M7CL, the program change of the corresponding program number will be transmitted on the Tx channel shown in the list. (If an event is assigned to more than one program number on the same channel, the lowestnumbered program number will be transmitted.) If you turn on the OMNI button / BANK button in Single mode, operation will change as follows. • When the OMNI button is on ........... Program changes of all MIDI channels will be received. However, regardless of the MIDI channel that is received, the event assigned to the corresponding program number of the Rx channel will be executed. Turning on the OMNI button will not change the operation for program change transmission. • When the BANK button is on ........... The CH indication in the list will change to BANK (bank number), and bank select (control change #0, #32) + program change messages can be transmitted and received. This is convenient when you want to control more than 128 events on a single MIDI channel. When bank select and then program change messages (in that order) are received on the Rx channel, the event assigned to that bank number and program number in the list will be executed. When you execute a specific event on the M7CL, bank select + program change messages for the bank number and program number assigned to that event will be transmitted on the Tx channel. (If the same event is assigned more than once in the list, the lowest-numbered bank number and program number will be transmitted.) NOTE • The settings of the OMNI and BANK buttons are ignored in Multi mode. • If the BANK button is on and only a program change on an applicable MIDI channel is received, the last-selected bank number will be used. MIDI 17 HINT • If the BANK button is on, the OMNI button can also be turned on at the same time. In this case, bank select + program change messages of all MIDI channels will be received. M7CL Owner's Manual 185