Yamaha M7CL M7cl V1 Owner's Manual - Page 150
TALKBACK IN field, INPUT TO TALKBACK field, TALKBACK ON button, ASSIGN field
![]() |
View all Yamaha M7CL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 150 highlights
Using talkback 2 Press the popup button or the ASSIGN field to open the TALKBACK popup window. In this popup window you can make detailed settings for talkback. 1 2 43 1 TALKBACK IN field • +48V button ...This is an on/off switch for the phantom power (+48V) supplied to the TALKBACK jack. • TALKBACK jack level ...........This indicates the input level of the mic connected to the TALKBACK jack. B INPUT TO TALKBACK field • Input select button ...........Opens the INPUT PORT SELECT popup window, where you can select the INPUT jack used for talkback. • +48V button ...........This is an on/off switch for the phantom power (+48V) supplied to the INPUT jack used for talkback. • GAIN knob .....Adjusts the input sensitivity of the INPUT jack used for talkback. Use the corresponding multifunction encoder to make this adjustment. You can also use the MONITOR screen GAIN knob to adjust this. • Input level ......Indicates the input level of the mic connected to the INPUT jack used for talkback. C TALKBACK ON button Switches talkback on/off. This operation can also be performed using the MONITOR screen TALKBACK ON button. D ASSIGN field Selects the bus(es) to which the talkback signal will be sent. You can press the CLEAR ALL button to defeat all selections. 3 Connect a mic to the front panel TALKBACK jack, and turn the TALKBACK GAIN knob to adjust the input sensitivity of the mic. The meter in the TALKBACK IN field indicates the input level of the mic connected to the TALKBACK jack. If you want phantom power (+48V) to be supplied to the TALKBACK jack, turn on the +48V button located in the TALKBACK IN field. 4 If you want to use an INPUT jack 1-32 {1- 48} as supplementary input for talkback, proceed as follows. 1 Press the INPUT TO TALKBACK field INPUT select button to open the INPUT PORT SELECT popup window. 2 Of the IN 1-32 (1-48) buttons, press the but- ton for the input you want to use for talkback, making it light. You can select only one input at a time. 3 Press the CLOSE button to close the popup window. Use the INPUT TO TALKBACK field GAIN knob and level meter to adjust the input level of the connected mic. NOTE • The PAD will be internally switched on or off when the HA gain is adjusted between -14 dB and -13 dB. Keep in mind that noise may be generated if there is a difference between the Hot and Cold output impedance of the external device connected to the INPUT connector when using phantom power. 5 Press a button in the ASSIGN field to specify the bus(es) to which the talkback signal will be sent (multiple selections are allowed). These buttons correspond to the following buses. MIX 1-16 buttons MTRX 1-8 buttons ST L, ST R buttons MONO (C) button MIX buses 1-16 MATRIX buses 1-8 STEREO bus L/R MONO bus HINT • You can press the CLEAR ALL button to defeat all selections. 6 To enable talkback, press the TALKBACK ON button to turn it on. The TALKBACK ON button will alternately turn on/ off each time you press the button (Latch operation). While talkback is on, the signal from the TALKBACK jack and the selected INPUT jack will be output to the destination bus. HINT • You can also assign talkback on/off or an ASSIGN change to a user-defined key. In this case, you can select either latched operation or unlatched operation (the function will be on only while you continue holding down the key) (→ p. 200). • When talkback is on, you can use the talkback dimmer to lower the monitor levels other than talkback (→ p. 143). 150 M7CL Owner's Manual
![](/manual_guide/products/yamaha-m7cl-m7cl-v1-owners-manual-022fa08/150.png)