Home » Dell Manuals » Servers » Dell PowerEdge XL 5133-4 » Manual Viewer

Dell PowerEdge XL 5133-4 Dell PowerEdge FTOS Command Line Reference Guide for - Page 83

boot write net config retries, boot zero, default gateway, enable,

View all Dell PowerEdge XL 5133-4 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

boot write net config retries Set the number of retries for network boot configuration failure. Syntax boot write net config retries Command Modes uBoot Command History Example Version 8.3.17.0 u Supported on M I/O Aggregator Figure 6-2. boot write net config retries Command Example BOOT_USER # boot write net config retries 2 Updated number of Network Boot Config retries to 2. BOOT_USER # boot zero Clears the primary, secondary, or default boot parameters. Syntax boot zero [primary | secondary | default] Command Modes uBoot Command History Version 8.3.17.0 u Supported on M I/O Aggregator default gateway Set the default gateway IP address. Syntax default-gateway Command Modes uBoot Command History Version 8.3.17.0 u Supported on M I/O Aggregator enable Change the access privilege level. Syntax enable [user | admin] Command Modes uBoot Command History Version 8.3.17.0 u Supported on M I/O Aggregator u-Boot | 81

Section	Page
About this Guide	7
Objectives	7
Audience	7
Conventions	7
Related Documents	8
Before You Start	9
Default Settings	9
Other Auto-Configured Settings	9
DCB Support	10
FCoE Connectivity	10
iSCSI Operation	10
Link Aggregation	11
Link Tracking	11
VLANs	11
Uplink LAG	11
Server-Facing LAGs	12
Stacking Mode	12
Where to Go From Here	12
CLI Basics	15
Accessing the Command Line	15
Multiple Configuration Users	16
Navigating the Command Line Interface	16
Obtaining Help	17
Using the Keyword no	19
Filtering show Commands	19
Displaying All Output	20
Filtering Command Output Multiple Times	20
Command Modes	20
EXEC Mode	20
EXEC Privilege Mode	20
CONFIGURATION Mode	20
INTERFACE Mode	21
LINE Mode	21
MONITOR SESSION Mode	21
PROTOCOL LLDP Mode	22
File Management	23
Overview	23
Basic File Management Commands	23
Control and Monitoring	41
Commands	41
Important Points to Remember	64
u-Boot	81
Overview	81
Commands	81
Data Center Bridging	91
Overview	91
DCB Command	91
PFC Commands	91
ETS Commands	91
DCBX Commands	91
Dynamic Host Configuration Protocol (DHCP)	109
Overview	109
DHCP Client Commands	109
Other Commands supported by DHCP Client	109
FIP Snooping	115
Overview	115
FIP Snooping Commands	115
Internet Group Management Protocol (IGMP)	123
IGMP Commands	123
Important Points to Remember	123
Interfaces	129
Overview	129
Port Interface Commands	129
Port Channel Commands	130
Time Domain Reflectometer (TDR) Commands	130
Important Points to Remember	130
Virtual LAN (VLAN) Commands	131
IPv4 Routing	163
IP Commands	163
iSCSI Optimization	179
Overview	179
iSCSI Commands	179
Link Aggregation Control Protocol (LACP)	183
Overview	183
LACP Commands	183
Layer 2	187
Overview	187
MAC Addressing Commands	187
Virtual LAN (VLAN) Commands	187
Link Layer Discovery Protocol (LLDP)	191
Overview	191
LLDP Commands	191
Port Monitoring	195
Overview	195
Monitoring Commands	195
Important Points to Remember	195
Quality of Service (QoS)	201
Overview	201
Policy-Based QoS Commands	201
Security	203
Commands	203
Authentication and Password Commands	203
SSH Server and SCP Commands	203
Simple Network Management Protocol (SNMP) and Syslog	211
Overview	211
SNMP Commands	211
Important Points to Remember	211
Syslog Commands	211
Stacking Commands	223
Overview	223
Stacking Commands	223
Storm Control	229
Overview	229
Storm Control Commands	229
System Time	231
Overview	231
Time Commands	231
Uplink Failure Detection (UFD)	239
Overview	239
UFD Commands	239
Debugging and Diagnostics	247
Offline Diagnostic Commands	247
Important Points to Remember	247
Hardware Commands	247