Yamaha AW4416 Reference Guide - Page 171
t recall a scene during recording, t change input patches during recording
View all Yamaha AW4416 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 171 highlights
Appendix • The stereo track may be in playback mode. • Is the input signal routed appropriately to the recorder? * * If the signal is being input appropriately to the recorder, pressing the [REC TRACK SELECT] key will cause the meter in the FL display to react. • When a file input/output page such as the SONG screen Song List page is displayed, recording and playback are not possible. • CD/DAT DIGITAL REC in the UTILITY screen Prefer.2 page may be set to DISABLE. • Please read and understand the copyright warning (¡ P.36) before using digital input signals. sCan't record on the STEREO track • It is not possible to record on the STEREO track while recording on other tracks. sCan't play back the STEREO track • Muting may be selected in the TRACK screen Ste- reo page. • Are monitor channels 1 and 2 raised? * * For STEREO track playback mode, the signal is output from monitor channels 1 and 2. sNot all tracks will play back • There are limitations on the number of tracks that can be simultaneously recorded or played. Refer to Operation Guide P.147 "Audio tracks". sThe volume of a particular channel increases or decreases • Are the dynamics processor settings appropriate? • EQ may have been recorded in the automix. sFaders move to the lowest position on their own • Automix may have been recorded. • Faders 9-14 cannot be operated when the mixing layer is 17-24/RTN. sMeters move even though the faders are lowered • The direct out setting may be PRE EQ or PRE FADER. • The meter display may be set to PRE FADER. sCan't store a scene • Is the scene memory protected? • A scene cannot be stored in scene number 00. sCan't reproduce a scene • One or more channels may be set to Recall Safe. sCan't recall a scene during recording • The AW4416 may be set to record the digital input signal. • Make sure that CD/DAT DIGITAL REC is set to ENABLE. sCan't change input patches during recording • The AW4416 may be set to record the digital input signal. • Make sure that CD/DAT DIGITAL REC in the UTILITY screen Prefer.2 page is set to ENABLE. sCan't save to a library • It is not possible to save to the factory-preset libraries. sCan't recall a channel library to the stereo output channel • Channel libraries saved from other channels cannot be recalled to the stereo output channel. sCan't exchange MIDI data • Are the MIDI cables connected correctly? • A MIDI cable may be broken. • Is the power turned on for the transmitting and receiving devices? • Do the channel settings match for the transmitted and receiving devices? • In the MIDI screen MIDI Setup page, is PORT SELECT effect to MIDI? • In the MIDI screen MIDI Setup page, are PRO- GRAM CHANGE TX and RX set to ON? • Is a scene assigned to the program change num- ber being transmitted? sMIDI messages are looped • In the MIDI screen MIDI Setup page, ECHO may be turned ON. • Also check the settings of the connected external MIDI devices. sMTC messages are not transmitted • Is the MIDI cable correctly connected to the MTC OUT connector? MTC is not transmitted from the MIDI OUT connector. • Is SYNC OUT set correctly? • Is MTC SYNC set to MASTER? sThe AW4416 does not synchronize to incoming MTC messages • Is the MIDI cable connected to the MIDI IN connector? • In the MIDI screen MIDI Sync page, is MTC Sync set to SLAVE? sMTC messages are received, but synchronization drifts • Is a large amount of MIDI data (notes etc.) being received together with the MTC messages? sMTC synchronization drifts • Does the frame rate match between the AW4416 and the external device? • SYNC OFFSET may have been set. • If jumps occur in the synchronized time, change the SYNC AVE. setting in the MIDI screen MIDI Sync page, and try again. Appendix-36 - Reference Guide