Home » Kyocera Manuals » Laser Printers » Kyocera FS-9100DN » Manual Viewer

Kyocera FS-9100DN FS-9100/9500 Operation Guide Rev-1.3 - Page 56

Paper Handling, MP Tray Mode, Cassette Mode, First Mode Automatic Manual Feeding, ENTER

UPC - 632983001066

Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

2.2.12 Paper Handling You can change the MP tray mode, the paper size and type for each paper source, the sorter mode, the paper source, and paper destinations. MP Tray Mode The MP tray can be used in one of two modes: cassette mode or first mode. The MP tray can hold approximately 200 sheets of paper (A4 size, 0.11 mm thickness). Q Cassette Mode The cassette mode provides faster printing speed than the first mode. Approximately 200 sheets of paper can be continuously fed in this mode. (This is the factory setting.) Q First Mode (Automatic Manual Feeding) The printer automatically feeds any paper placed on the MP tray even if another paper source is selected. After all paper in the MP tray is printed, paper will be fed from the paper source originally selected. 1 Press the MENU key. 2 Press the 3 or 4 key repeatedly until Paper Handling > appears. Paper Handling > 3 Press the 2 key. 4 Press the 3 or 4 key repeatedly until >MP Tray Mode appears. >MP Tray Mode Cassette 5 Press the ENTER key. A blinking question mark (?) appears. >MP Tray Mode ? Cassette 6 Select First or Cassette using the 3 or 4 key. 7 Press the ENTER key. 8 Press the MENU key. The message display returns to Ready. Chapter 3 Using the Operator Panel Setting the MP Tray Size When using the MP tray in the cassette mode, you should set the MP tray size to the paper size that is used to format the job to print. If they do not match, printing will not be made on the correct size paper when automatic paper size selection is made by the application (printer driver). The factory setting is A4 or Letter size. For more details about the paper sizes that can be fed from the MP tray, see Chapter 5 Paper Selection. 1 Press the MENU key. 2 Press the 3 or 4 key repeatedly until Paper Handling > appears. Paper Handling > 3 Press the 2 key. 4 Press the 3 or 4 key repeatedly until >MP Tray Size appears. >MP Tray Size A4 5 Press the ENTER key. A blinking question mark (?) appears. >MP Tray Size ? A4 3-40

Section	Page
Operation Guide ver 1.3	1
Contents	5
Introduction	7
For More Information...	7
Guide to the Operation Guide	7
IMPORTANT! PLEASE READ FIRST	8
Chapter 1 Names of Parts	12
Chapter 2 How to Load Paper	14
1. How to Load Paper	14
1.1 Loading Paper into the Paper Cassette	14
1.2 Loading Paper into the MP (Multi-Purpose) Tray	15
1.3 Setting Envelopes	16
Chapter 3 Using the Operator Panel	17
1. Understanding the Operator Panel	17
1.1 Operation Indicators	18
1.2 Message Display	18
1.3 Interface Indicator	18
1.4 Paper Size Indicator	19
1.5 Paper Type Indicator	19
1.6 Keys	19
2. Using the Operator Panel	20
2.1 Menu Selection System	20
2.2 Using the Menu Selection System	26
2.2.1 Printing the Menu Map	26
2.2.2 Printing Status Page	26
2.2.3 e-MPS	27
2.2.4 Changing the Interface Parameters	34
2.2.5 Changing the Emulation	38
2.2.6 Setting the Default Font	40
2.2.7 Using Page Set Menus	42
2.2.8 Setting the Print Quality	46
2.2.9 Operating an Option Hard Disk	47
2.2.10 Operating a RAM Disk	50
2.2.11 Operating a Memory Card	52
2.2.12 Paper Handling	56
2.2.13 Other Modes	63
Chapter 4 Troubleshooting	69
1. General Guide	69
2. Print Quality Problems	70
3. Indicators and Messages	72
3.1 Indicators	72
3.2 Maintenance Messages	72
3.3 Error Messages	74
4. Correcting a Paper Jam	76
4.1 Jam in Paper Cassette	77
4.2 Jam at the MP Tray	77
4.3 Jam in Left Cover 1	78
4.4 Jam in Left Cover 2	79
4.5 Paper Jam at the Option Document Finisher	79
Chapter 5 Paper Selection	80
1. General Guidelines	80
1.1 Paper Availability	80
1.2 Paper Specifications	80
1.3 Selecting the Right Paper	80
2. Special Paper	82
2.1 Transparency (Overhead Projection Film)	82
2.2 Adhesive-Backed Labels	83
3. Paper Type	84
Chapter 6 Maintenance	85
1. Toner Container Replacement	85
1.1 Toner Container Replacement Interval	85
1.2 Replenishing Toner	85
Appendix A Fonts	89
Appendix B Expansion Memory	93
1. Removing the Main Circuit Board	93
1.1 Notes on Handling the Main Circuit Board and DIMM	93
1.2 Removing the Main Circuit Board from the Printer	93
2. Installing DIMMs	94
2.1 Removing DIMM	94
2.2 Testing the Expansion Memory	94
Appendix C Host Computer Interface	95
1. Parallel Interface	95
1.1 Parallel Interface Communication Modes	95
1.2 Interface Signals	95
2. Serial Interface	96
2.1 Interface Signals	96
3. RS-232C Protocol	97
4. RS-232C Cable Connection	98
4.1 Preparing an RS-232C Cable	98
4.2 Connecting the RS-232C Cable	98
4.3 Setting the RS-232C Parameters	98
Appendix D Option Units	100
1. Available Options	100
2. Installing Option Units	102
2.1 PF-70/75 Paper Feeders	102
2.2 DF-70/71/75 Document Finishers	102
2.3 Network Interface	102
2.4 Hard Disk	103
2.5 Memory Card	103
Appendix E Specifications	104
Glossary	106
Index	108
A	108
B	108
C	108
D	108
E	108
F	108
G	108
H	108
I	108
J	108
K	108
L	108
M	108
N	109
O	109
P	109
R	109
S	109
T	109
V	109
W	109
Driver Guide ver 1.1	111
Contents	113
Chapter 1 Installing the Printer Driver	114
Chapter 2 Setting the Defaults	116
2.1 Adding Option Devices (Setup)	116
2.1.1 Installing the Paper Feeder (PF-70)	116
2.1.2 Installing the Paper Feeder (PF-75)	117
2.1.3 Installing the Document Finisher (DF-70/DF-71)	118
2.1.4 Installing the Document Finisher (DF-75)	119
2.1.5 Installing the Hard Disk	120
2.1.6 Using the RAM Disk	120
2.1.7 Selecting the User Name	121
2.1.8 Selecting the Printer Description Language	122
Chapter 3 Printing Through Application Software	124
3.1 Setting the Paper Size	124
3.1.1 Custom Size Settings	126
3.1.2 Advanced Media Settings	127
3.2 Setting the Duplex Printing	128
3.3 Using the Booklet Mode	129
3.4 Using the Document Finisher (DF-70/DF-71)	130
3.5 Using the Document Finisher (DF-75)	131
3.6 e-MPS	132
3.6.1 Using Job Retention	133
3.6.2 Using Virtual Mailbox Printing	138

Match case Limit results 1 per page

Chapter 3

Using the Operator Panel

3-40

2.2.12 Paper Handling

You can change the MP tray mode, the paper size and type for

each paper source, the sorter mode, the paper source, and pa-

per destinations.

MP Tray Mode

The MP tray can be used in one of two modes: cassette mode or

first mode. The MP tray can hold approximately 200 sheets of

paper (A4 size, 0.11 mm thickness).

Cassette Mode

The cassette mode provides faster printing speed than the first

mode. Approximately 200 sheets of paper can be continuously

fed in this mode. (This is the factory setting.)

First Mode (Automatic Manual Feeding)

The printer automatically feeds any paper placed on the MP tray

even if another paper source is selected. After all paper in the

MP tray is printed, paper will be fed from the paper source origi-

nally selected.

Press the

key.

Press the

key repeatedly until

Paper Han-

dling >

appears.

Press the

key.

Press the

key repeatedly until

>MP Tray Mode

appears.

Press the

ENTER

key. A blinking question mark (

) ap-

pears.

Select

First

Cassette

using the

key.

Press the

ENTER

key.

Press the

key. The message display returns to

Ready

Setting the MP Tray Size

When using the MP tray in the cassette mode, you should set

the MP tray size to the paper size that is used to format the job

to print. If they do not match, printing will not be made on the

correct size paper when automatic paper size selection is made

by the application (printer driver). The factory setting is A4 or

Letter size.

For more details about the paper sizes that can be fed from the

MP tray, see

Chapter 5 Paper Selection

Press the

key.

Press the

key repeatedly until

Paper Han-

dling >

appears.

Press the

key.

Press the

key repeatedly until

>MP Tray Size

appears.

Press the

ENTER

key. A blinking question mark (

) ap-

pears.

Paper Handling >

>MP Tray Mode

Cassette

>MP Tray Mode

? Cassette

Paper Handling >

>MP Tray Size

? A4