Home » Kyocera Manuals » Laser Printers » Kyocera FS-9100DN » Manual Viewer

Kyocera FS-9100DN FS-9100/9500 Operation Guide Rev-1.3 - Page 64

Others, >MSG Language, English, >Form Feed, Time Out 030sec., >Sleep timer, ENTER

UPC - 632983001066

Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

2 Press the 3 or 4 key repeatedly until Others > appears. Others > 3 Press the 2 key. 4 Press the 3 or 4 key repeatedly until >MSG Language appears. The default message language is English. >MSG Language English 5 To change the language, press the ENTER key. A blinking question mark (?) appears. >MSG Language ? English 6 Press the 3 key. The display cycles through the available selections in the following order (The 4 key cycles in the reverse order): English Francais Deutsch Italiano Nederlands 7 Press the ENTER key. 8 Press the MENU key. The message display returns to Ready. Automatic Form Feed Timeout Setting When the printer receives no data for a certain time, it times out and releases the current interface: it prints whatever data it has in its buffer and feeds out the page. You can adjust the time-out time as follows: 1 Press the MENU key. 2 Press the 3 or 4 key repeatedly until Others > appears. Others > Chapter 3 Using the Operator Panel 3 Press the 2 key. 4 Press the 3 or 4 key repeatedly until >Form Feed Time Out appears. The default setting is 30 seconds. >Form Feed Time Out 030sec. 5 Press the ENTER key. A blinking cursor (_) appears. >Form Feed Time Out 030sec. 6 Press the 3 or 4 key to increase or decrease the value of the figure where the cursor is blinking and set the desired time. The time can be set between 0 and 495 seconds, in 5-second increments. (The printer does not timeout with the value set to 0.) You can use the 2 and 1 keys to move the cursor right and left. 7 Display the desired time and press the ENTER key. 8 Press the MENU key. The message display returns to Ready. Sleep Timer Setting The printer has a sleep timer to conserve power when the printer is not printing, processing, or receiving data. You can adjust the timer value, the length of time the printer waits before entering sleeping mode in the absence of data. 1 Press the MENU key. 2 Press the 3 or 4 key repeatedly until Others > appears. Others > 3 Press the 2 key. 4 Press the 3 or 4 key repeatedly until >Sleep Timer > appears. The default setting is 030 min. >Sleep timer > 030 min. 5 Press the ENTER key. A blinking cursor ( _ ) appears. >Sleep timer > 030 min. 3-48

Section	Page
Operation Guide ver 1.3	1
Contents	5
Introduction	7
For More Information...	7
Guide to the Operation Guide	7
IMPORTANT! PLEASE READ FIRST	8
Chapter 1 Names of Parts	12
Chapter 2 How to Load Paper	14
1. How to Load Paper	14
1.1 Loading Paper into the Paper Cassette	14
1.2 Loading Paper into the MP (Multi-Purpose) Tray	15
1.3 Setting Envelopes	16
Chapter 3 Using the Operator Panel	17
1. Understanding the Operator Panel	17
1.1 Operation Indicators	18
1.2 Message Display	18
1.3 Interface Indicator	18
1.4 Paper Size Indicator	19
1.5 Paper Type Indicator	19
1.6 Keys	19
2. Using the Operator Panel	20
2.1 Menu Selection System	20
2.2 Using the Menu Selection System	26
2.2.1 Printing the Menu Map	26
2.2.2 Printing Status Page	26
2.2.3 e-MPS	27
2.2.4 Changing the Interface Parameters	34
2.2.5 Changing the Emulation	38
2.2.6 Setting the Default Font	40
2.2.7 Using Page Set Menus	42
2.2.8 Setting the Print Quality	46
2.2.9 Operating an Option Hard Disk	47
2.2.10 Operating a RAM Disk	50
2.2.11 Operating a Memory Card	52
2.2.12 Paper Handling	56
2.2.13 Other Modes	63
Chapter 4 Troubleshooting	69
1. General Guide	69
2. Print Quality Problems	70
3. Indicators and Messages	72
3.1 Indicators	72
3.2 Maintenance Messages	72
3.3 Error Messages	74
4. Correcting a Paper Jam	76
4.1 Jam in Paper Cassette	77
4.2 Jam at the MP Tray	77
4.3 Jam in Left Cover 1	78
4.4 Jam in Left Cover 2	79
4.5 Paper Jam at the Option Document Finisher	79
Chapter 5 Paper Selection	80
1. General Guidelines	80
1.1 Paper Availability	80
1.2 Paper Specifications	80
1.3 Selecting the Right Paper	80
2. Special Paper	82
2.1 Transparency (Overhead Projection Film)	82
2.2 Adhesive-Backed Labels	83
3. Paper Type	84
Chapter 6 Maintenance	85
1. Toner Container Replacement	85
1.1 Toner Container Replacement Interval	85
1.2 Replenishing Toner	85
Appendix A Fonts	89
Appendix B Expansion Memory	93
1. Removing the Main Circuit Board	93
1.1 Notes on Handling the Main Circuit Board and DIMM	93
1.2 Removing the Main Circuit Board from the Printer	93
2. Installing DIMMs	94
2.1 Removing DIMM	94
2.2 Testing the Expansion Memory	94
Appendix C Host Computer Interface	95
1. Parallel Interface	95
1.1 Parallel Interface Communication Modes	95
1.2 Interface Signals	95
2. Serial Interface	96
2.1 Interface Signals	96
3. RS-232C Protocol	97
4. RS-232C Cable Connection	98
4.1 Preparing an RS-232C Cable	98
4.2 Connecting the RS-232C Cable	98
4.3 Setting the RS-232C Parameters	98
Appendix D Option Units	100
1. Available Options	100
2. Installing Option Units	102
2.1 PF-70/75 Paper Feeders	102
2.2 DF-70/71/75 Document Finishers	102
2.3 Network Interface	102
2.4 Hard Disk	103
2.5 Memory Card	103
Appendix E Specifications	104
Glossary	106
Index	108
A	108
B	108
C	108
D	108
E	108
F	108
G	108
H	108
I	108
J	108
K	108
L	108
M	108
N	109
O	109
P	109
R	109
S	109
T	109
V	109
W	109
Driver Guide ver 1.1	111
Contents	113
Chapter 1 Installing the Printer Driver	114
Chapter 2 Setting the Defaults	116
2.1 Adding Option Devices (Setup)	116
2.1.1 Installing the Paper Feeder (PF-70)	116
2.1.2 Installing the Paper Feeder (PF-75)	117
2.1.3 Installing the Document Finisher (DF-70/DF-71)	118
2.1.4 Installing the Document Finisher (DF-75)	119
2.1.5 Installing the Hard Disk	120
2.1.6 Using the RAM Disk	120
2.1.7 Selecting the User Name	121
2.1.8 Selecting the Printer Description Language	122
Chapter 3 Printing Through Application Software	124
3.1 Setting the Paper Size	124
3.1.1 Custom Size Settings	126
3.1.2 Advanced Media Settings	127
3.2 Setting the Duplex Printing	128
3.3 Using the Booklet Mode	129
3.4 Using the Document Finisher (DF-70/DF-71)	130
3.5 Using the Document Finisher (DF-75)	131
3.6 e-MPS	132
3.6.1 Using Job Retention	133
3.6.2 Using Virtual Mailbox Printing	138

Match case Limit results 1 per page

Chapter 3

Using the Operator Panel

3-48

Press the

key repeatedly until

Others >

ap-

pears.

Press the

key.

Press the

key repeatedly until

>MSG

Language

appears. The default message language is

English.

To change the language, press the

ENTER

key. A

blinking question mark (

) appears.

Press the

key. The display cycles through the avail-

able selections in the following order (The

key cycles

in the reverse order):

English

Francais

Deutsch

Italiano

Nederlands

Press the

ENTER

key.

Press the

key. The message display returns to

Ready

Automatic Form Feed Timeout Setting

When the printer receives no data for a certain time, it times out

and releases the current interface: it prints whatever data it has

in its buffer and feeds out the page. You can adjust the time-out

time as follows:

Press the

key.

Press the

key repeatedly until

Others >

ap-

pears.

Press the

key.

Press the

key repeatedly until

>Form Feed

Time Out

appears. The default setting is 30 seconds.

Press the

ENTER

key. A blinking cursor (

) appears.

Press the

key to increase or decrease the value

of the figure where the cursor is blinking and set the

desired time. The time can be set between 0 and 495

seconds, in 5-second increments. (The printer does not

timeout with the value set to 0.) You can use the

and

keys to move the cursor right and left.

Display the desired time and press the

ENTER

key.

Press the

key. The message display returns to

Ready

Sleep Timer Setting

The printer has a sleep timer to conserve power when the print-

er is not printing, processing, or receiving data. You can adjust

the timer value, the length of time the printer waits before enter-

ing sleeping mode in the absence of data.

Press the

key.

Press the

key repeatedly until

Others >

ap-

pears.

Press the

key.

Press the

key repeatedly until

>Sleep Timer

appears. The default setting is

030 min

Press the

ENTER

key. A blinking cursor (

) appears.

Others

>MSG Language

English

>MSG Language

? English

Others

>Form Feed

Time Out 030sec.

>Form Feed

Time Out 030

sec.

Others

>Sleep timer

030 min.

>Sleep timer

030

min.