Kyocera FS-9100DN FS-9100/9500 Operation Guide Rev-1.3 - Page 63

Chapter 3

Using the Operator Panel

3-47

Press the

ENTER

key. A question mark (

?

) appears.

Press the

ENTER

key. All the customized paper weight

and duplex path settings will be reset to the default.

The message display returns to

Ready

.

Q

Verifying the Total Printed Pages and Resetting the Ton-

er Counter

You can display the total number of pages printed by your print-

er for confirmation whenever necessary. The total number of

printed pages can also be checked on the status page. More-

over, for proper maintenance scheduling, it will be necessary to

reset the toner counter using this menu each time a new toner

container is installed.

Q

Verifying the Total Printed Pages

This procedure only displays the total number of printed pages.

The number cannot be changed.

Press the

MENU

key.

Press the

3

or

4

key repeatedly until

Life

Counters >

appears.

Press the

2

key.

Press the

3

or

4

key until

>Total Print

appears.

Press the

MENU

key. The message display returns to

Ready

.

Q

Resetting the Remaining Toner Counter

If the toner container was replaced when

Replace toner

Clean Printer

was not displayed, reset the toner counter as

follows so that an accurate toner gauge measurement is indi-

cated on the status page. Note that if this operation is per-

formed when the toner container is not replaced, the toner

gauge measurement will not be indicated correctly. Also refer to

the Installation Guide supplied with the toner kit when replacing

the toner container.

Press the

MENU

key.

Press the

3

or

4


Life

Counters >

appears.

Press the

2

key.

Press the

3

or

4


>New Toner

Installed

appears

Press the

ENTER

key. A question mark (?) appears.

Press the

ENTER

key. The toner counter is reset.

Press the

MENU

key. The message display returns to

Ready

.

2.2.13 Other Modes

The modes described in the following pages can be accessed in

the Others submenu. To enter the Others submenu, press the

2

key while

Others >

is displayed.

The following submenus can be displayed by pressing the

2

key and then the

3

or

4

key.

• Message Language Selecting

• Automatic Form Feed Timeout Setting

• Sleep Timer Setting

• Received Data Dumping

• Printer Resetting

• Resource Setting

• Alarm (Buzzer) Setting

• Auto Continue Setting

• Service Menu (for service personnel)

Message Language Selecting

You can select the language of the messages on the message

display by following the procedure given below.

Press the

MENU

key.

>Reset Type

Adjust ?

Life Counters

>

>Total Print

0123456

5

6

1

2

3

4

5

1

Life Counters

>

>New Toner

Installed

>New Toner

Installed ?

2

3

4

5

6

7

1

Section	Page
Operation Guide ver 1.3	1
Contents	5
Introduction	7
For More Information...	7
Guide to the Operation Guide	7
IMPORTANT! PLEASE READ FIRST	8
Chapter 1 Names of Parts	12
Chapter 2 How to Load Paper	14
1. How to Load Paper	14
1.1 Loading Paper into the Paper Cassette	14
1.2 Loading Paper into the MP (Multi-Purpose) Tray	15
1.3 Setting Envelopes	16
Chapter 3 Using the Operator Panel	17
1. Understanding the Operator Panel	17
1.1 Operation Indicators	18
1.2 Message Display	18
1.3 Interface Indicator	18
1.4 Paper Size Indicator	19
1.5 Paper Type Indicator	19
1.6 Keys	19
2. Using the Operator Panel	20
2.1 Menu Selection System	20
2.2 Using the Menu Selection System	26
2.2.1 Printing the Menu Map	26
2.2.2 Printing Status Page	26
2.2.3 e-MPS	27
2.2.4 Changing the Interface Parameters	34
2.2.5 Changing the Emulation	38
2.2.6 Setting the Default Font	40
2.2.7 Using Page Set Menus	42
2.2.8 Setting the Print Quality	46
2.2.9 Operating an Option Hard Disk	47
2.2.10 Operating a RAM Disk	50
2.2.11 Operating a Memory Card	52
2.2.12 Paper Handling	56
2.2.13 Other Modes	63
Chapter 4 Troubleshooting	69
1. General Guide	69
2. Print Quality Problems	70
3. Indicators and Messages	72
3.1 Indicators	72
3.2 Maintenance Messages	72
3.3 Error Messages	74
4. Correcting a Paper Jam	76
4.1 Jam in Paper Cassette	77
4.2 Jam at the MP Tray	77
4.3 Jam in Left Cover 1	78
4.4 Jam in Left Cover 2	79
4.5 Paper Jam at the Option Document Finisher	79
Chapter 5 Paper Selection	80
1. General Guidelines	80
1.1 Paper Availability	80
1.2 Paper Specifications	80
1.3 Selecting the Right Paper	80
2. Special Paper	82
2.1 Transparency (Overhead Projection Film)	82
2.2 Adhesive-Backed Labels	83
3. Paper Type	84
Chapter 6 Maintenance	85
1. Toner Container Replacement	85
1.1 Toner Container Replacement Interval	85
1.2 Replenishing Toner	85
Appendix A Fonts	89
Appendix B Expansion Memory	93
1. Removing the Main Circuit Board	93
1.1 Notes on Handling the Main Circuit Board and DIMM	93
1.2 Removing the Main Circuit Board from the Printer	93
2. Installing DIMMs	94
2.1 Removing DIMM	94
2.2 Testing the Expansion Memory	94
Appendix C Host Computer Interface	95
1. Parallel Interface	95
1.1 Parallel Interface Communication Modes	95
1.2 Interface Signals	95
2. Serial Interface	96
2.1 Interface Signals	96
3. RS-232C Protocol	97
4. RS-232C Cable Connection	98
4.1 Preparing an RS-232C Cable	98
4.2 Connecting the RS-232C Cable	98
4.3 Setting the RS-232C Parameters	98
Appendix D Option Units	100
1. Available Options	100
2. Installing Option Units	102
2.1 PF-70/75 Paper Feeders	102
2.2 DF-70/71/75 Document Finishers	102
2.3 Network Interface	102
2.4 Hard Disk	103
2.5 Memory Card	103
Appendix E Specifications	104
Glossary	106
Index	108
A	108
B	108
C	108
D	108
E	108
F	108
G	108
H	108
I	108
J	108
K	108
L	108
M	108
N	109
O	109
P	109
R	109
S	109
T	109
V	109
W	109
Driver Guide ver 1.1	111
Contents	113
Chapter 1 Installing the Printer Driver	114
Chapter 2 Setting the Defaults	116
2.1 Adding Option Devices (Setup)	116
2.1.1 Installing the Paper Feeder (PF-70)	116
2.1.2 Installing the Paper Feeder (PF-75)	117
2.1.3 Installing the Document Finisher (DF-70/DF-71)	118
2.1.4 Installing the Document Finisher (DF-75)	119
2.1.5 Installing the Hard Disk	120
2.1.6 Using the RAM Disk	120
2.1.7 Selecting the User Name	121
2.1.8 Selecting the Printer Description Language	122
Chapter 3 Printing Through Application Software	124
3.1 Setting the Paper Size	124
3.1.1 Custom Size Settings	126
3.1.2 Advanced Media Settings	127
3.2 Setting the Duplex Printing	128
3.3 Using the Booklet Mode	129
3.4 Using the Document Finisher (DF-70/DF-71)	130
3.5 Using the Document Finisher (DF-75)	131
3.6 e-MPS	132
3.6.1 Using Job Retention	133
3.6.2 Using Virtual Mailbox Printing	138

Kyocera FS-9100DN FS-9100/9500 Operation Guide Rev-1.3 - Page 63

Other Modes, Verifying the Total Printed s and Resetting the Ton - maintenance kit

Page 63 highlights