Home » Kyocera Manuals » Laser Printers » Kyocera FS-9100DN » Manual Viewer

Kyocera FS-9100DN FS-9100/9500 Operation Guide Rev-1.3 - Page 65

Others, >Sleep timer, >>Sleep Mode, >Print HEX-DUMP, Processing, Waiting, ENTER

UPC - 632983001066

Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Chapter 3 Using the Operator Panel 6 Press the 3 or 4 key to increase or decrease the value of the figure where the cursor is blinking and set the desired time. The timer can be set between 5 and 240 min, in 5-minute increments. You can use the 2 and 1 keys to move the cursor right and left. 7 Press the ENTER key. 8 Press the MENU key. The message display returns to Ready. Q Turning Off the Sleep Timer You can turn off the sleep timer function by following the procedure given below. 1 Press the MENU key. 2 Press the 3 or 4 key repeatedly until Others > appears. Others > 3 Press the 2 key. 4 Press the 3 or 4 key repeatedly until >Sleep Timer >appears. >Sleep timer > 030 min. 5 Press the 2 key and display >>Sleep Mode. >>Sleep Mode On 6 Press the ENTER key. A blinking question mark (?) appears. >>Sleep Mode ? On 7 Select Off using the 3 or 4 key. >>Sleep Mode ? Off 8 Press the ENTER key. 9 Press the MENU key. The message display returns to Ready. 3-49 Received Data Dumping It is possible to print data received by the printer as hexadecimal code for the purposes of debugging programs and files. 1 Press the MENU key. 2 Press the 3 or 4 key repeatedly until Others > appears. Others > 3 Press the 2 key. 4 Press the 3 or 4 key repeatedly until >Print HEX- DUMP appears. >Print HEX-DUMP 5 Press the ENTER key. A question mark (?) appears. >Print HEX-DUMP? 6 Press the ENTER key again. Processing appears for a second, and then Waiting appears. Processing Waiting 7 Send data to be dumped to the printer. The message Processing will be displayed while receiving the data. Once the dumped data you require has been printed, it is possible to cancel the printing of any further dumped data by taking the printer offline by pressing the GO key and then pressing the CANCEL key. 8 Once all data has been received, the message Waiting will appear. Press the GO key to finish printing. Printer Resetting The procedure described below resets the printer's temporary conditions, such as the current unit of measurement, page orientation, font, character code set, margins, etc., set by commands to their default values.

Section	Page
Operation Guide ver 1.3	1
Contents	5
Introduction	7
For More Information...	7
Guide to the Operation Guide	7
IMPORTANT! PLEASE READ FIRST	8
Chapter 1 Names of Parts	12
Chapter 2 How to Load Paper	14
1. How to Load Paper	14
1.1 Loading Paper into the Paper Cassette	14
1.2 Loading Paper into the MP (Multi-Purpose) Tray	15
1.3 Setting Envelopes	16
Chapter 3 Using the Operator Panel	17
1. Understanding the Operator Panel	17
1.1 Operation Indicators	18
1.2 Message Display	18
1.3 Interface Indicator	18
1.4 Paper Size Indicator	19
1.5 Paper Type Indicator	19
1.6 Keys	19
2. Using the Operator Panel	20
2.1 Menu Selection System	20
2.2 Using the Menu Selection System	26
2.2.1 Printing the Menu Map	26
2.2.2 Printing Status Page	26
2.2.3 e-MPS	27
2.2.4 Changing the Interface Parameters	34
2.2.5 Changing the Emulation	38
2.2.6 Setting the Default Font	40
2.2.7 Using Page Set Menus	42
2.2.8 Setting the Print Quality	46
2.2.9 Operating an Option Hard Disk	47
2.2.10 Operating a RAM Disk	50
2.2.11 Operating a Memory Card	52
2.2.12 Paper Handling	56
2.2.13 Other Modes	63
Chapter 4 Troubleshooting	69
1. General Guide	69
2. Print Quality Problems	70
3. Indicators and Messages	72
3.1 Indicators	72
3.2 Maintenance Messages	72
3.3 Error Messages	74
4. Correcting a Paper Jam	76
4.1 Jam in Paper Cassette	77
4.2 Jam at the MP Tray	77
4.3 Jam in Left Cover 1	78
4.4 Jam in Left Cover 2	79
4.5 Paper Jam at the Option Document Finisher	79
Chapter 5 Paper Selection	80
1. General Guidelines	80
1.1 Paper Availability	80
1.2 Paper Specifications	80
1.3 Selecting the Right Paper	80
2. Special Paper	82
2.1 Transparency (Overhead Projection Film)	82
2.2 Adhesive-Backed Labels	83
3. Paper Type	84
Chapter 6 Maintenance	85
1. Toner Container Replacement	85
1.1 Toner Container Replacement Interval	85
1.2 Replenishing Toner	85
Appendix A Fonts	89
Appendix B Expansion Memory	93
1. Removing the Main Circuit Board	93
1.1 Notes on Handling the Main Circuit Board and DIMM	93
1.2 Removing the Main Circuit Board from the Printer	93
2. Installing DIMMs	94
2.1 Removing DIMM	94
2.2 Testing the Expansion Memory	94
Appendix C Host Computer Interface	95
1. Parallel Interface	95
1.1 Parallel Interface Communication Modes	95
1.2 Interface Signals	95
2. Serial Interface	96
2.1 Interface Signals	96
3. RS-232C Protocol	97
4. RS-232C Cable Connection	98
4.1 Preparing an RS-232C Cable	98
4.2 Connecting the RS-232C Cable	98
4.3 Setting the RS-232C Parameters	98
Appendix D Option Units	100
1. Available Options	100
2. Installing Option Units	102
2.1 PF-70/75 Paper Feeders	102
2.2 DF-70/71/75 Document Finishers	102
2.3 Network Interface	102
2.4 Hard Disk	103
2.5 Memory Card	103
Appendix E Specifications	104
Glossary	106
Index	108
A	108
B	108
C	108
D	108
E	108
F	108
G	108
H	108
I	108
J	108
K	108
L	108
M	108
N	109
O	109
P	109
R	109
S	109
T	109
V	109
W	109
Driver Guide ver 1.1	111
Contents	113
Chapter 1 Installing the Printer Driver	114
Chapter 2 Setting the Defaults	116
2.1 Adding Option Devices (Setup)	116
2.1.1 Installing the Paper Feeder (PF-70)	116
2.1.2 Installing the Paper Feeder (PF-75)	117
2.1.3 Installing the Document Finisher (DF-70/DF-71)	118
2.1.4 Installing the Document Finisher (DF-75)	119
2.1.5 Installing the Hard Disk	120
2.1.6 Using the RAM Disk	120
2.1.7 Selecting the User Name	121
2.1.8 Selecting the Printer Description Language	122
Chapter 3 Printing Through Application Software	124
3.1 Setting the Paper Size	124
3.1.1 Custom Size Settings	126
3.1.2 Advanced Media Settings	127
3.2 Setting the Duplex Printing	128
3.3 Using the Booklet Mode	129
3.4 Using the Document Finisher (DF-70/DF-71)	130
3.5 Using the Document Finisher (DF-75)	131
3.6 e-MPS	132
3.6.1 Using Job Retention	133
3.6.2 Using Virtual Mailbox Printing	138

Match case Limit results 1 per page

Chapter 3

Using the Operator Panel

3-49

Press the

key to increase or decrease the value

of the figure where the cursor is blinking and set the

desired time. The timer can be set between 5 and 240

min, in 5-minute increments. You can use the

and

keys to move the cursor right and left.

Press the

ENTER

key.

Press the

key. The message display returns to

Ready

Turning Off the Sleep Timer

You can turn off the sleep timer function by following the proce-

dure given below.

Press the

key.

Press the

key repeatedly until

Others >

ap-

pears.

Press the

key.

Press the

key repeatedly until

>Sleep Timer

appears.

Press the

key and display

>>Sleep Mode

Press the

ENTER

key. A blinking question mark (

) ap-

pears.

Select

Off

using the

key.

Press the

ENTER

key.

Press the

key. The message display returns to

Ready

Received Data Dumping

It is possible to print data received by the printer as hexadeci-

mal code for the purposes of debugging programs and files.

Press the

key.

Press the

key repeatedly until

Others >

ap-

pears.

Press the

key.

Press the

key repeatedly until

>Print HEX-

DUMP

appears.

Press the

ENTER

key. A question mark (

) appears.

Press the

ENTER

key again.

Processing

appears for

a second, and then

Waiting

appears.

Send data to be dumped to the printer. The message

Processing

will be displayed while receiving the da-

ta.

Once the dumped data you require has been printed, it

is possible to cancel the printing of any further dumped

data by taking the printer offline by pressing the

key and then pressing the

CANCEL

key.

Once all data has been received, the message

Wait-

ing

will appear. Press the

key to finish printing.

Printer Resetting

The procedure described below resets the printer’s temporary

conditions, such as the current unit of measurement, page ori-

entation, font, character code set, margins, etc., set by com-

mands to their default values.

Others

>Sleep timer

030 min.

>>Sleep Mode

? On

>>Sleep Mode

? Off

Others

>Print HEX-DUMP

>Print HEX-DUMP?

Processing

Waiting