Home » Kyocera Manuals » Laser Printers » Kyocera FS-9100DN » Manual Viewer

Kyocera FS-9100DN FS-9100/9500 Operation Guide Rev-1.3 - Page 87

tact with the grid cleaner pad, push and pull the main

UPC - 632983001066

Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Chapter 6 Maintenance 10 Remove the seal from the rear of the old waste toner box, and then close the opening of the box with the seal. Seal up the old waste toner box with the supplied plastic bag and dispose of it. 13 Pull the main charger approximately 5 cm (2 inches) out. 11 Gently pull the cleaning knob as far as it will go, push and pull it several times, and then push it back in. 14 While avoiding the main charger roller (A) to be in contact with the grid cleaner pad, push and pull the main charger several times. (Do not push the main charger all the way in. Otherwise, water from the pad will cause the main charger unit to become we and this may affect printing.) 12 Take out the new grid cleaner from the protective bag, and then remove the cap from the grid cleaner. (A) When the grid is clean, remove the grid cleaner from the printer and dispose of it. The grid cleaner is not reusable. 15 Fit the new waste toner box to the printer. 6-3

Section	Page
Operation Guide ver 1.3	1
Contents	5
Introduction	7
For More Information...	7
Guide to the Operation Guide	7
IMPORTANT! PLEASE READ FIRST	8
Chapter 1 Names of Parts	12
Chapter 2 How to Load Paper	14
1. How to Load Paper	14
1.1 Loading Paper into the Paper Cassette	14
1.2 Loading Paper into the MP (Multi-Purpose) Tray	15
1.3 Setting Envelopes	16
Chapter 3 Using the Operator Panel	17
1. Understanding the Operator Panel	17
1.1 Operation Indicators	18
1.2 Message Display	18
1.3 Interface Indicator	18
1.4 Paper Size Indicator	19
1.5 Paper Type Indicator	19
1.6 Keys	19
2. Using the Operator Panel	20
2.1 Menu Selection System	20
2.2 Using the Menu Selection System	26
2.2.1 Printing the Menu Map	26
2.2.2 Printing Status Page	26
2.2.3 e-MPS	27
2.2.4 Changing the Interface Parameters	34
2.2.5 Changing the Emulation	38
2.2.6 Setting the Default Font	40
2.2.7 Using Page Set Menus	42
2.2.8 Setting the Print Quality	46
2.2.9 Operating an Option Hard Disk	47
2.2.10 Operating a RAM Disk	50
2.2.11 Operating a Memory Card	52
2.2.12 Paper Handling	56
2.2.13 Other Modes	63
Chapter 4 Troubleshooting	69
1. General Guide	69
2. Print Quality Problems	70
3. Indicators and Messages	72
3.1 Indicators	72
3.2 Maintenance Messages	72
3.3 Error Messages	74
4. Correcting a Paper Jam	76
4.1 Jam in Paper Cassette	77
4.2 Jam at the MP Tray	77
4.3 Jam in Left Cover 1	78
4.4 Jam in Left Cover 2	79
4.5 Paper Jam at the Option Document Finisher	79
Chapter 5 Paper Selection	80
1. General Guidelines	80
1.1 Paper Availability	80
1.2 Paper Specifications	80
1.3 Selecting the Right Paper	80
2. Special Paper	82
2.1 Transparency (Overhead Projection Film)	82
2.2 Adhesive-Backed Labels	83
3. Paper Type	84
Chapter 6 Maintenance	85
1. Toner Container Replacement	85
1.1 Toner Container Replacement Interval	85
1.2 Replenishing Toner	85
Appendix A Fonts	89
Appendix B Expansion Memory	93
1. Removing the Main Circuit Board	93
1.1 Notes on Handling the Main Circuit Board and DIMM	93
1.2 Removing the Main Circuit Board from the Printer	93
2. Installing DIMMs	94
2.1 Removing DIMM	94
2.2 Testing the Expansion Memory	94
Appendix C Host Computer Interface	95
1. Parallel Interface	95
1.1 Parallel Interface Communication Modes	95
1.2 Interface Signals	95
2. Serial Interface	96
2.1 Interface Signals	96
3. RS-232C Protocol	97
4. RS-232C Cable Connection	98
4.1 Preparing an RS-232C Cable	98
4.2 Connecting the RS-232C Cable	98
4.3 Setting the RS-232C Parameters	98
Appendix D Option Units	100
1. Available Options	100
2. Installing Option Units	102
2.1 PF-70/75 Paper Feeders	102
2.2 DF-70/71/75 Document Finishers	102
2.3 Network Interface	102
2.4 Hard Disk	103
2.5 Memory Card	103
Appendix E Specifications	104
Glossary	106
Index	108
A	108
B	108
C	108
D	108
E	108
F	108
G	108
H	108
I	108
J	108
K	108
L	108
M	108
N	109
O	109
P	109
R	109
S	109
T	109
V	109
W	109
Driver Guide ver 1.1	111
Contents	113
Chapter 1 Installing the Printer Driver	114
Chapter 2 Setting the Defaults	116
2.1 Adding Option Devices (Setup)	116
2.1.1 Installing the Paper Feeder (PF-70)	116
2.1.2 Installing the Paper Feeder (PF-75)	117
2.1.3 Installing the Document Finisher (DF-70/DF-71)	118
2.1.4 Installing the Document Finisher (DF-75)	119
2.1.5 Installing the Hard Disk	120
2.1.6 Using the RAM Disk	120
2.1.7 Selecting the User Name	121
2.1.8 Selecting the Printer Description Language	122
Chapter 3 Printing Through Application Software	124
3.1 Setting the Paper Size	124
3.1.1 Custom Size Settings	126
3.1.2 Advanced Media Settings	127
3.2 Setting the Duplex Printing	128
3.3 Using the Booklet Mode	129
3.4 Using the Document Finisher (DF-70/DF-71)	130
3.5 Using the Document Finisher (DF-75)	131
3.6 e-MPS	132
3.6.1 Using Job Retention	133
3.6.2 Using Virtual Mailbox Printing	138