Dell PowerEdge 2970 Hardware Owner's Manual - Page 104

Removing the Center Riser Board, Lift the center riser board from the two guide pins on either end

Get Dell PowerEdge 2970 PDF manuals and user guides View all Dell PowerEdge 2970 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Removing the Center Riser Board CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. See your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. 1 Press the blue release tab in the center of the center riser to release the board from the system board socket while easing both ends of the riser upward. 2 Lift the center riser board from the two guide pins on either end, and draw the riser away from the system board. Figure 3-31. Replacing the Center Riser Board 3 2 1 4 5 1 pin collars (2) 4 guide pins (2) 2 release tab 5 system board socket 3 center riser board Installing the Center Riser Board 1 Fitting the two pin collars over the guide pins on the system board, gently lower the center riser board until the board connector is firmly seated into the system board socket. See Figure 3-31. 104 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
104
Installing System Components
Removing the Center Riser Board
CAUTION:
Only trained service technicians are authorized to remove the system cover and access any of the
components inside the system. See your
Product Information Guide
for complete information about safety
precautions, working inside the computer, and protecting against electrostatic discharge.
1
Press the blue release tab in the center of the center riser to release the board from the system board
socket while easing both ends of the riser upward.
2
Lift the center riser board from the two guide pins on either end, and draw the riser away from the
system board.
Figure 3-31.
Replacing the Center Riser Board
Installing the Center Riser Board
1
Fitting the two pin collars over the guide pins on the system board, gently lower the center riser board
until the board connector is firmly seated into the system board socket. See Figure 3-31.
1
pin collars (2)
2
release tab
3
center riser board
4
guide pins (2)
5
system board socket
4
3
2
5
1