Dell PowerEdge 2970 Hardware Owner's Manual - Page 22

Fan Redundancy, CPU # IERR, CPU # Thermtrip, CPU # Presence, E141C, CPU Mismatch, CPU Protocol - bios

Get Dell PowerEdge 2970 PDF manuals and user guides View all Dell PowerEdge 2970 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Table 1-6. LCD Status Messages (continued) Code E1311 E1313 E1410 E1414 E1418 E141C E141F Text RPM Fan Mod ## Fan Redundancy CPU # IERR CPU # Thermtrip CPU # Presence CPU Mismatch CPU Protocol Causes Corrective Actions RPM of specified cooling fan is See "Troubleshooting System out of acceptable operating range. Cooling Problems" on page 123. The system is no longer fan- Check control panel LCD for redundant. Another fan failure additional scrolling messages. See will put the system at risk of over- "Troubleshooting System Cooling heating. Problems" on page 123. Processor # has had an internal error (IERR) that is possibly, but not always, caused by a problem with the CPU. See "Getting Help" on page 147. Specified microprocessor is out of See "Troubleshooting System acceptable temperature range and Cooling Problems" on page 123. has halted operation. If the problem persists, ensure that the microprocessor heat sinks are properly installed. See "Troubleshooting the Microprocessors" on page 133. NOTE: The LCD continues to display this message until the system's power cord is disconnected and reconnected to the AC power source, or the SEL is cleared using either Server Assistant or the BMC Management Utility. See the Dell OpenManage Baseboard Management Controller User's Guide for information about these utilities. Specified processor is missing or See "Troubleshooting the bad, and the system is in an Microprocessors" on page 133. unsupported configuration. Processors are in a configuration unsupported by Dell. Ensure that your processors match and conform to the type described in the Microprocessor Technical Specifications outlined in your system's Getting Started Guide. The system BIOS has reported a See "Getting Help" on page 147. processor protocol error. 22 About Your System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
22
About Your System
E1311
RPM Fan Mod ##
RPM of specified cooling fan is
out of acceptable operating range.
See "Troubleshooting System
Cooling Problems" on page 123.
E1313
Fan Redundancy
The system is no longer fan-
redundant. Another fan failure
will put the system at risk of over-
heating.
Check control panel LCD for
additional scrolling messages. See
"Troubleshooting System Cooling
Problems" on page 123.
E1410
CPU # IERR
Processor # has had an internal
error (IERR) that is possibly, but
not always, caused by a problem
with the CPU.
See "Getting Help" on page 147.
E1414
CPU # Thermtrip
Specified microprocessor is out of
acceptable temperature range and
has halted operation.
See "Troubleshooting System
Cooling Problems" on page 123.
If the problem persists, ensure
that the microprocessor heat
sinks are properly installed. See
"Troubleshooting the
Microprocessors" on page 133.
NOTE:
The LCD continues to
display this message until the
system’s power cord is
disconnected and reconnected to
the AC power source, or the SEL is
cleared using either Server
Assistant or the BMC Management
Utility. See the
Dell OpenManage
Baseboard Management
Controller User’s Guide
for
information about these utilities.
E1418
CPU # Presence
Specified processor is missing or
bad, and the system is in an
unsupported configuration.
See "Troubleshooting the
Microprocessors" on page 133.
E141C
CPU Mismatch
Processors are in a configuration
unsupported by Dell.
Ensure that your processors
match and conform to the type
described in the Microprocessor
Technical Specifications outlined
in your system’s
Getting Started
Guide
.
E141F
CPU Protocol
The system BIOS has reported a
processor protocol error.
See "Getting Help" on page 147.
Table 1-6.
LCD Status Messages
(continued)
Code
Text
Causes
Corrective Actions