Dell PowerEdge 2970 Hardware Owner's Manual - Page 108

Installing the SAS/SATA Backplane Board

Get Dell PowerEdge 2970 PDF manuals and user guides View all Dell PowerEdge 2970 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

Figure 3-33. SAS/SATA Backplane Board Removal 2 3 1 4 5 1 drive carrier 4 securing slots (12) 2 SAS-backplane board release 3 SAS/SATA backplane board pin 5 securing tabs (12) Installing the SAS/SATA Backplane Board CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. See your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. 1 Place the SAS/SATA backplane board so that the securing tabs on the drive cage are fully inserted into the securing slots on the backplane board. See Figure 3-33. 2 Pull the backplane board release pin. See Figure 3-33. 3 While pulling the release pin, tilt the backplane board toward the front of the system until it stops, then release the release pin and ensure that it snaps into place. 4 Reinstall the SAS controller daughter card. See "Installing a SAS Controller Daughter Card" on page 65. 5 Reattach the SAS controller daughter card cables. 108 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
108
Installing System Components
Figure 3-33.
SAS/SATA Backplane Board Removal
Installing the SAS/SATA Backplane Board
CAUTION:
Only trained service technicians are authorized to remove the system cover and access any of the
components inside the system. See your
Product Information Guide
for complete information about safety
precautions, working inside the computer, and protecting against electrostatic discharge.
1
Place the SAS/SATA backplane board so that the securing tabs on the drive cage are fully inserted into
the securing slots on the backplane board. See Figure 3-33.
2
Pull the backplane board release pin. See Figure 3-33.
3
While pulling the release pin, tilt the backplane board toward the front of the system until it stops,
then release the release pin and ensure that it snaps into place.
4
Reinstall the SAS controller daughter card. See "Installing a SAS Controller Daughter Card" on
page 65.
5
Reattach the SAS controller daughter card cables.
1
drive carrier
2
SAS-backplane board release
pin
3
SAS/SATA backplane board
4
securing slots (12)
5
securing tabs (12)
2
1
5
3
4