Epson Stylus Pro 9000 User Manual - Page 99

Installing an Interface Card, On the FireWire card, make sure DIP switch 10 is set

Get Epson Stylus Pro 9000 - Print Engine PDF manuals and user guides View all Epson Stylus Pro 9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

A-2 | Installing an Interface Card 2. Use a Phillips-head (+) screwdriver to remove the two screws securing the shield plate to the back of the printer. Then lift off the plate. Be sure to keep the screws so you can use them if you re-install the shield plate. 3. Make sure you set any jumpers or DIP switches on the card. See the card's documentation for details. On the FireWire card, make sure DIP switch 10 is set to ON (advanced mode). 4. Slide the interface card along the slots on both sides of the compartment. Push it in firmly to fully insert the connector into the printer's internal socket. A-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
A-2
A-2
|
Installing an Interface Card
2.
Use a Phillips-head (+) screwdriver to remove the two screws securing
the shield plate to the back of the printer. Then lift off the plate.
Be sure to keep the screws so you can use them if you re-install the shield
plate.
3.
Make sure you set any jumpers or DIP switches on the card. See the
card’s documentation for details.
On the FireWire card, make sure DIP switch 10 is set to
ON
(advanced
mode).
4.
Slide the interface card along the slots on both sides of the
compartment. Push it in firmly to fully insert the connector into the
printer’s internal socket.