HP 9000 rp4410-4 User Service Guide, Fifth Edition - HP 9000 rp4410/4440 - Page 164

Replacing the Front Cover Dipswitch Setting for S5

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 164 highlights

2. Set the lower of the two blocks when the processor carrier is oriented with the extractor handles toward you. • Set the dipswitch to the right (ON) position for PA-RISC. Do not disturb switch banks 1 through 4 beneath the sheet metal. Figure 6-13 Dipswitch Setting for S5 3. Align the processor extender board with the front and rear card guides. 4. Slide the processor extender board down until it begins to seat in the socket located on the midplane riser board. 5. To fully seat the processor extender board into the socket on the midplane riser board, push the extraction levers inward to the locked position. 6. Replace the front cover. See "Replacing the Front Cover" (page 153). 7. Replace the front bezel. See "Replacing the Front Bezel" (page 152). 8. Verify processor operation by using the system utilities. • To verify operation, use the iLO MP commands and the BCH commands. • To exercise the processor, use the MAKODIAG provided by the offline diagnostic environment. 164 Removing and Replacing Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
2.
Set the lower of the two blocks when the processor carrier is oriented with the extractor
handles toward you.
•
Set the dipswitch to the right (ON) position for PA-RISC. Do not disturb switch banks
1 through 4 beneath the sheet metal.
Figure 6-13 Dipswitch Setting for S5
3.
Align the processor extender board with the front and rear card guides.
4.
Slide the processor extender board down until it begins to seat in the socket located on the
midplane riser board.
5.
To fully seat the processor extender board into the socket on the midplane riser board, push
the extraction levers inward to the locked position.
6.
Replace the front cover. See
“Replacing the Front Cover” (page 153)
.
7.
Replace the front bezel. See
“Replacing the Front Bezel” (page 152)
.
8.
Verify processor operation by using the system utilities.
•
To verify operation, use the iLO MP commands and the BCH commands.
•
To exercise the processor, use the
MAKODIAG
provided by the offline diagnostic
environment.
164
Removing and Replacing Components