HP 9000 rp4410-4 User Service Guide, Fifth Edition - HP 9000 rp4410/4440 - Page 65

Replacing the Front Cover, Removing the Top Cover, Extend the Server, from the Rack

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

1. If rack-mounted, slide the server out from the rack until it stops. (See "Extend the Server from the Rack" (page 58)) 2. Remove the front bezel. (See "Removing the Front Bezel" (page 63).) 3. Loosen the four captive thumbscrews that hold the front cover in place. Figure 3-12 Removing and Replacing the Front Cover 4. Raise the cover slightly, and pull the cover toward the front of the server to free the tabs from the slots in the center of the chassis. Replacing the Front Cover To replace the front cover, follow these steps: 1. Align the tabs at the rear of the front cover with the corresponding slots in the chassis and fully seat the tabs into the slots. 2. Tighten the four thumbscrews securely. 3. Replace the front bezel. See "Replacing the Front Bezel" (page 64). Removing the Top Cover To remove the top cover, follow these steps: 1. If rack-mounted, slide the server out from the rack until it stops. See "Extend the Server from the Rack" (page 58). 2. Loosen the two captive thumbscrews that hold the top cover in place. 3. Pull the cover toward the rear of the server to free the tabs from the slots in the center of the chassis and lift the cover straight up. Installing Additional Components 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
1.
If rack-mounted, slide the server out from the rack until it stops. (See
“Extend the Server
from the Rack” (page 58)
)
2.
Remove the front bezel. (See
“Removing the Front Bezel” (page 63)
.)
3.
Loosen the four captive thumbscrews that hold the front cover in place.
Figure 3-12 Removing and Replacing the Front Cover
4.
Raise the cover slightly, and pull the cover toward the front of the server to free the tabs
from the slots in the center of the chassis.
Replacing the Front Cover
To replace the front cover, follow these steps:
1.
Align the tabs at the rear of the front cover with the corresponding slots in the chassis and
fully seat the tabs into the slots.
2.
Tighten the four thumbscrews securely.
3.
Replace the front bezel. See
“Replacing the Front Bezel” (page 64)
.
Removing the Top Cover
To remove the top cover, follow these steps:
1.
If rack-mounted, slide the server out from the rack until it stops. See
“Extend the Server
from the Rack” (page 58)
.
2.
Loosen the two captive thumbscrews that hold the top cover in place.
3.
Pull the cover toward the rear of the server to free the tabs from the slots in the center of the
chassis and lift the cover straight up.
Installing Additional Components
65