HP 9000 rp4410-4 User Service Guide, Fifth Edition - HP 9000 rp4410/4440 - Page 201

Installing the Server Components, Verify the Upgrade Installation

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 201 highlights

Figure 6-38 Connecting SCSI Cable B to the SCSI Adapter Board 7. Close the swivel latch on top of the hot-pluggable disk drive cage. 8. Replace the two hot-pluggable disk drives into the disk drive cage. Installing the Server Components To Install the necessary components in the server chassis, follow these steps: 1. Install the processor extender board. See "Replacing the Processor Extender Board" (page 162). 2. Install the memory extender board. See "Replacing the Memory Extender Board" (page 156). 3. Install the front cover. See "Replacing the Front Cover" (page 153). 4. Install the front bezel. See "Replacing the Front Bezel" (page 152). Verify the Upgrade Installation After completing the upgrade, verify that the sever is ready for operation as follows: 1. Reconnect AC power to rear panel connectors. 2. Press the front panel power button to power on the server. 3. Wait for completion of the POST. Verify that no errors have been detected. 4. At the BCH prompt, enter the in io command. Verify that all installed disk drives are recognized and operating correctly. 5. Initiate the OS and monitor operation. U320 SCSI Enablement and Conversion Procedures 201

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
Figure 6-38 Connecting SCSI Cable B to the SCSI Adapter Board
7.
Close the swivel latch on top of the hot-pluggable disk drive cage.
8.
Replace the two hot-pluggable disk drives into the disk drive cage.
Installing the Server Components
To Install the necessary components in the server chassis, follow these steps:
1.
Install the processor extender board. See
“Replacing the Processor Extender Board” (page 162)
.
2.
Install the memory extender board. See
“Replacing the Memory Extender Board” (page 156)
.
3.
Install the front cover. See
“Replacing the Front Cover” (page 153)
.
4.
Install the front bezel. See
“Replacing the Front Bezel” (page 152)
.
Verify the Upgrade Installation
After completing the upgrade, verify that the sever is ready for operation as follows:
1.
Reconnect AC power to rear panel connectors.
2.
Press the front panel power button to power on the server.
3.
Wait for completion of the POST. Verify that no errors have been detected.
4.
At the BCH prompt, enter the
in io
command. Verify that all installed disk drives are
recognized and operating correctly.
5.
Initiate the OS and monitor operation.
U320 SCSI Enablement and Conversion Procedures
201