IBM x3655 Service Guide - Page 95

Installing, 5-inch-drive, backplane

Get IBM x3655 - System - 7985 PDF manuals and user guides
UPC - 883436014533
View all IBM x3655 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Installing the 3.5-inch-drive backplane To install the replacement 3.5-inch-drive backplane, complete the following steps. 3.5-inch hot-swap drive backplane Mounting pins 1. Orient the replacement hard disk drive backplane so that the connectors for the hard-disk drives face the front of the server. 2. Place the notches that are at the bottom of the hard disk drive backplane frame onto the pins that are on the lower outside of the hard-disk-drive enclosure. 3. Push the top of the hard disk drive backplane toward the front of the server until it clicks into place. Make sure the release latches hold the backplane securely in place. 4. Connect the power and signal cables to the hard disk drive backplane. 5. Install the fan bracket assembly (see "Installing the fan-bracket assembly" on page 67). 6. Install the cover (see "Installing the cover" on page 40). 7. Slide the server into the rack. 8. Insert the hard disk drives into the bays. 9. Connect the cables and power cords. 10. Turn on all attached devices and the server. Chapter 3. Removing and replacing server components 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
Installing
the
3.5-inch-drive
backplane
To
install
the
replacement
3.5-inch-drive
backplane,
complete
the
following
steps.
3.5-inch hot-swap
drive backplane
Mounting pins
1.
Orient
the
replacement
hard
disk
drive
backplane
so
that
the
connectors
for
the
hard-disk
drives
face
the
front
of
the
server.
2.
Place
the
notches
that
are
at
the
bottom
of
the
hard
disk
drive
backplane
frame
onto
the
pins
that
are
on
the
lower
outside
of
the
hard-disk-drive
enclosure.
3.
Push
the
top
of
the
hard
disk
drive
backplane
toward
the
front
of
the
server
until
it
clicks
into
place.
Make
sure
the
release
latches
hold
the
backplane
securely
in
place.
4.
Connect
the
power
and
signal
cables
to
the
hard
disk
drive
backplane.
5.
Install
the
fan
bracket
assembly
(see
“Installing
the
fan-bracket
assembly”
on
page
67).
6.
Install
the
cover
(see
“Installing
the
cover”
on
page
40).
7.
Slide
the
server
into
the
rack.
8.
Insert
the
hard
disk
drives
into
the
bays.
9.
Connect
the
cables
and
power
cords.
10.
Turn
on
all
attached
devices
and
the
server.
Chapter
3.
Removing
and
replacing
server
components
77