Dell PowerEdge T300 Hardware Owner's Manual (PDF) - Page 31

BIOS Update Attempt, Caution! NVRAM_CLR - updates

Get Dell PowerEdge T300 PDF manuals and user guides View all Dell PowerEdge T300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Table 1-6. System Messages (continued) Message Causes Corrective Actions Alert! Unsupported Unsupported DIMMs, memory, incomplete mismatched DIMMs, or sets, or unmatched unmatched DIMMs have sets. The following been detected. If more memory is disabled: than one DIMM is present, DIMMs must be installed in matching pairs. For memory configuration information, see "Memory Module Installation Guidelines" on page 110. If the problem persists, see "Troubleshooting System Memory" on page 146. Attempting to update Remote Configuration. Please wait... Remote Configuration Wait until the process is request has been detected complete. and is being processed. BIOS Update Attempt Remote BIOS update Failed! attempt failed. Retry the BIOS update. If the problem persists, see "Getting Help" on page 175. Caution! NVRAM_CLR NVRAM_CLR jumper is Remove the NVRAM_CLR jumper is installed installed. CMOS has been jumper. See Figure 6-1 for on system board. cleared. jumper location. Decreasing available memory Faulty or improperly installed memory modules. See "Troubleshooting System Memory" on page 146. Diskette drive 0 seek failure. Faulty or improperly inserted diskette, incorrect configuration settings in the System Setup program, or loose diskette/tape drive interface cable, or loose power cable. Replace the diskette. See "Troubleshooting a Diskette Drive" on page 149. Diskette read failure. Faulty diskette, faulty or improperly connected diskette/tape drive interface cable, or loose power cable. See "Troubleshooting a Diskette Drive" on page 149. About Your System 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
About Your System
31
Alert! Unsupported
memory, incomplete
sets, or unmatched
sets. The following
memory is disabled:
Unsupported DIMMs,
mismatched DIMMs, or
unmatched DIMMs have
been detected. If more
than one DIMM is
present, DIMMs must be
installed in matching
pairs.
For memory configuration
information, see "Memory
Module Installation
Guidelines" on page 110. If
the problem persists, see
"Troubleshooting System
Memory" on page 146.
Attempting to
update Remote
Configuration.
Please wait...
Remote Configuration
request has been detected
and is being processed.
Wait until the process is
complete.
BIOS Update Attempt
Failed!
Remote BIOS update
attempt failed.
Retry the BIOS update. If
the problem persists, see
"Getting Help" on page 175.
Caution! NVRAM_CLR
jumper is installed
on system board.
NVRAM_CLR jumper is
installed. CMOS has been
cleared.
Remove the NVRAM_CLR
jumper. See Figure 6-1 for
jumper location.
Decreasing
available memory
Faulty or improperly
installed memory
modules.
See "Troubleshooting System
Memory" on page 146.
Diskette drive 0
seek failure.
Faulty or improperly
inserted diskette,
incorrect configuration
settings in the System
Setup program, or loose
diskette/tape drive
interface cable, or loose
power cable. Replace the
diskette.
See "Troubleshooting a
Diskette Drive" on page 149.
Diskette read
failure.
Faulty diskette, faulty or
improperly connected
diskette/tape drive
interface cable, or loose
power cable.
See "Troubleshooting a
Diskette Drive" on page 149.
Table 1-6.
System Messages
(continued)
Message
Causes
Corrective Actions