Dell PowerEdge T300 Hardware Owner's Manual (PDF) - Page 79

Install the hard drive carrier on the hard drive.,

Get Dell PowerEdge T300 PDF manuals and user guides View all Dell PowerEdge T300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

NOTICE: Combining SATA and SAS hard drives in the same system configuration is not supported. 1 Unpack the hard drive and prepare it for installation. 2 Remove the front bezel (see "Removing the Front Bezel" on page 63). 3 Remove either the existing hard drive, if applicable, or the hard drive carrier (see "Diskette Drive (Optional)" on page 84). 4 Install the hard drive carrier on the hard drive. a Insert the hard drive into the hard-drive carrier with the connector end of the drive at the rear. See Figure 3-12. b Viewing the assembly as shown in Figure 3-12, align the screw holes on the hard drive with the rear set of holes labeled "SAS" on the hard drive carrier. When aligned correctly, the rear of the hard drive will be flush with the rear of the hard-drive carrier. c Attach the four screws to secure the hard drive to the hard-drive carrier. See Figure 3-12. Installing System Components 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Installing System Components
79
NOTICE:
Combining SATA and SAS hard drives in the same system configuration is
not supported.
1
Unpack the hard drive and prepare it for installation.
2
Remove the front bezel (see "Removing the Front Bezel" on page 63).
3
Remove either the existing hard drive, if applicable, or the hard drive
carrier (see "Diskette Drive (Optional)" on page 84).
4
Install the hard drive carrier on the hard drive.
a
Insert the hard drive into the hard-drive carrier with the connector
end of the drive at the rear. See
Figure 3-12
.
b
Viewing the assembly as shown in
Figure 3-12, a
lign the screw holes
on the hard drive with the rear set of holes labeled "SAS" on the hard
drive carrier.
When aligned correctly, the rear of the hard drive will be flush with
the rear of the hard-drive carrier.
c
Attach the four screws to secure the hard drive to the hard-drive
carrier. See
Figure 3-12
.