Dell PowerEdge T610 Hardware Owner's Manual - Page 150

two processor sockets only one touch point is visible

Get Dell PowerEdge T610 PDF manuals and user guides View all Dell PowerEdge T610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

• SAS backplane cable from BP_PWR connector • Internal SD module cable from the J_SDCARD connector • Internal USB module cable from the INT_USB connector 15 Carefully route any loose cables away from the edges of the system board. 16 Remove the system board from the chassis: a Pull and hold the blue system board release pin. See Figure 3-27. b While holding the release pin, slide the system board towards the front of the system. See Figure 3-27. WARNING: Do not lift the system board by the memory modules latches or any component on the system board. c Grip the system board by the two blue touch points, located near the two processor sockets (only one touch point is visible in Figure 3-27). d Lift the system board up slightly to remove the system board securing slots from the metal hooks in the chassis. e Lift the connector end of the system board up at an angle, and lift the system board out of the chassis. See Figure 3-27. 150 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
150
Installing System Components
•
SAS backplane cable from BP_PWR connector
•
Internal SD module cable from the J_SDCARD connector
•
Internal USB module cable from the INT_USB connector
15
Carefully route any loose cables away from the edges of the system board.
16
Remove the system board from the chassis:
a
Pull and hold the blue system board release pin. See Figure 3-27.
b
While holding the release pin, slide the system board towards the
front of the system. See Figure 3-27.
WARNING:
Do not lift the system board by the memory modules latches or any
component on the system board.
c
Grip the system board by the two blue touch points, located near the
two processor sockets (only one touch point is visible in Figure 3-27).
d
Lift the system board up slightly to remove the system board securing
slots from the metal hooks in the chassis.
e
Lift the connector end of the system board up at an angle, and lift the
system board out of the chassis. See Figure 3-27.