Panasonic WJHD316A WJHD309A User Guide - Page 49

ABOUT THE EVENT FUNCTION, Action at an event occurrence

Get Panasonic WJHD316A - DIGITAL DISK RECORDER PDF manuals and user guides View all Panasonic WJHD316A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

ABOUT THE EVENT FUNCTION The event action will be performed when the following events occur. • Motion detection: When motion is detected by the motion detection function (see below), this is stated as an event of motion detection. • Video Loss: When a video signal supply is stopped because of a cable disconnection or malfunction of a camera, this is stated as an event of video loss. • Terminal alarm: When a signal is supplied from an external device such as a door sensor to the ALARM terminal, this is stated as an event of the terminal alarm. • Command alarm: When a command alarm is supplied from a PC connected to the SERIAL connector on the rear panel of this unit, this is stated as an event of the command alarm. About the Motion Detection Function (VMD) An alarm signal will be supplied when motion (luminance transition) is detected in a designated area. It is possible to save images recorded in the place where motion is detected, or send e-mails when motion is detected. Refer to a system administrator for further information about the required settings for the motion detection function such as the settings of the detection area. I Action at an event occurrence The event action will be performed according to the settings when an event occurs. There are 2 event action modes, the alarm mode (ALARM) and the activity detection mode (ACT DET), for each event type. The event action will be different according to the event action mode set. When an event of the alarm mode (ALARM) occurs, this unit activates the alarm action. About the event action mode G Alarm Mode (ALARM) This mode announces an event occurrence outside. Action taken in the alarm mode is referred to as the alarm action. G Activity Detection Mode (ACT DET) This mode records images in the place where an event occurred without announcing it. G OFF Only recording the event log is applicable. Any other event actions are not applicable. Event Action Alarm Mode Activity Detection Mode OFF Start recording.  Displays event information on the monitor.  Blinks the alarm indicator.   - - - - - Sounds the buzzer.  * Switches from a dis- played image to the  image from the location of the alarm occurrence. * Moves a camera to the preset position.  * Announces an event occurrence by sending  e-mails. * Announces an event occurrence by the PS·Data/Serial (RS232C)  commands. - - - -  - - - - - Supplies a signal from the ALARM connector or the ALARM/CONTROL con-  nector on the rear panel of this unit (Alarm signal out- put). Records the event log.  * Transmits images to an  FTP server. - -   - -  : Applicable - : Not applicable * : Available only when using a PC via a network (Refer to the Network Setup Instructions (PDF) for further information.) 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
49
Event Action
ABOUT THE EVENT FUNCTION
The event action will be performed when the following
events occur.
•
Motion detection:
When motion is detected by the
motion detection function (see below), this is stated as
an event of motion detection.
•
Video Loss:
When a video signal supply is stopped
because of a cable disconnection or malfunction of a
camera, this is stated as an event of video loss.
•
Terminal alarm:
When a signal is supplied from an
external device such as a door sensor to the ALARM
terminal, this is stated as an event of the terminal alarm.
•
Command alarm:
When a command alarm is supplied
from a PC connected to the SERIAL connector on the
rear panel of this unit, this is stated as an event of the
command alarm.
About the Motion Detection Function (VMD)
An alarm signal will be supplied when motion (luminance
transition) is detected in a designated area. It is possible to
save images recorded in the place where motion is detect-
ed, or send e-mails when motion is detected.
Refer to a system administrator for further information about
the required settings for the motion detection function such
as the settings of the detection area.
■
Action at an event occurrence
The event action will be performed according to the set-
tings when an event occurs.
There are 2 event action modes, the alarm mode (ALARM)
and the activity detection mode (ACT DET), for each event
type. The event action will be different according to the
event action mode set.
When an event of the alarm mode (ALARM) occurs, this unit
activates the alarm action.
About the event action mode
●
Alarm Mode (ALARM)
This mode announces an event occurrence outside. Action
taken in the alarm mode is referred to as the alarm action.
●
Activity Detection Mode (ACT DET)
This mode records images in the place where an event
occurred without announcing it.
●
OFF
Only recording the event log is applicable. Any other event
actions are not applicable.
✓
: Applicable
– : Not applicable
* : Available only when using a PC via a network (Refer to
the Network Setup Instructions (PDF) for further informa-
tion.)
Alarm
Mode
Activity
Detection Mode
OFF
–
–
–
–
–
–
–
–
–
✓
–
Start recording.
Displays event information
on the monitor.
Sounds the buzzer.
Blinks the alarm indicator.
* Switches from a dis-
played image to the
image from the location
of the alarm occurrence.
* Moves a camera to the
preset position.
* Announces an event
occurrence by sending
e-mails.
* Announces an event
occurrence by the
PS·Data/Serial (RS232C)
commands.
Supplies a signal from the
ALARM connector or the
ALARM/CONTROL con-
nector on the rear panel of
this unit (Alarm signal out-
put).
Records the event log.
* Transmits images to an
FTP server.
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
–
–
–
–
✓
–
–
–
✓
–