Dell PowerConnect B-RX16 Installation Guide - Page 51

Chassis lifting guidelines for BigIron RX-8 switches, Installing the BigIron RX-8 chassis in a rack

Get Dell PowerConnect B-RX16 PDF manuals and user guides View all Dell PowerConnect B-RX16 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Installing a BigIron RX-8 switch 2 Follow the steps given below to unpack a BigIron RX-8 chassis. 1. Move the pallet to a staging area as close to the installation site as possible. 2. Position the shipping carton with the arrows pointing up. 3. Remove the strap that secures the shipping carton to the pallet. 4. Remove the plastic cover and shipping carton. 5. Save the shipping carton, pallet, and packing materials in case you need to move or ship the chassis at a later time. Chassis lifting guidelines for BigIron RX-8 switches DANGER A fully-populated BigIron RX-8, chassis is heavy. TWO OR MORE PEOPLE ARE REQUIRED WHEN LIFTING, HANDLING, OR MOUNTING THESE DEVICES. Follow these guidelines for lifting and moving a BigIron RX-8 chassis: • Before lifting or moving the switch, disconnect all external cables. • Do not attempt to lift a fully configured switch by yourself. Using a mechanical lift to maneuver the switch into a rack is recommended. If a lift cannot be used, a minimum of four people must lift the switch, and you must remove components from the chassis before lifting. Installing the BigIron RX-8 chassis in a rack This section describes the following tasks: • "Preparing to mount a BigIron RX-8 chassis in a rack" • "Removing BigIron RX-8 extra shipment screws" • "Mounting a BigIron RX-8 chassis in a rack" • "Removing the slot blanks" Preparing to mount a BigIron RX-8 chassis in a rack Because of the weight of a fully loaded BigIron RX-8 chassis, Brocade recommends mounting a chassis in a rack before installing the modules and AC power supplies if necessary. In a standard 19-inch (EIA310-D) rack, you can install up to six BigIron RX-8 chassis. For each BigIron RX-8 chassis that you install in a rack, you must provide four standard #12-24 pan-head screws with which to mount and secure the chassis. Before performing this task, you should have an assembled rack and a #2 Phillips-head screwdriver. Removing BigIron RX-8 extra shipment screws The BigIron RX-8 ships with two extra screws installed in the right side of the chassis. These screws secure the fan tray, protecting it from damage during shipment. You must remove these screws before installing the chassis. Figure 25 shows the location of the screws. BigIron RX Installation Guide 39 53-1001811-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
BigIron RX Installation Guide
39
53-1001811-01
Installing a BigIron RX-8 switch
2
Follow the steps given below to unpack a BigIron RX-8 chassis.
1.
Move the pallet to a staging area as close to the installation site as possible.
2.
Position the shipping carton with the arrows pointing up.
3.
Remove the strap that secures the shipping carton to the pallet.
4.
Remove the plastic cover and shipping carton.
5.
Save the shipping carton, pallet, and packing materials in case you need to move or ship the
chassis at a later time.
Chassis lifting guidelines for BigIron RX-8 switches
DANGER
A fully-populated BigIron RX-8, chassis is heavy. TWO OR MORE PEOPLE ARE REQUIRED WHEN
LIFTING, HANDLING, OR MOUNTING THESE DEVICES.
Follow these guidelines for lifting and moving a BigIron RX-8 chassis:
•
Before lifting or moving the switch, disconnect all external cables.
•
Do not attempt to lift a fully configured switch by yourself. Using a mechanical lift to maneuver
the switch into a rack is recommended. If a lift cannot be used, a minimum of four people must
lift the switch, and you must remove components from the chassis before lifting.
Installing the BigIron RX-8 chassis in a rack
This section describes the following tasks:
•
“Preparing to mount a BigIron RX-8 chassis in a rack”
•
“Removing BigIron RX-8 extra shipment screws”
•
“Mounting a BigIron RX-8 chassis in a rack”
•
“Removing the slot blanks”
Preparing to mount a BigIron RX-8 chassis in a rack
Because of the weight of a fully loaded BigIron RX-8 chassis, Brocade recommends mounting a
chassis in a rack before installing the modules and AC power supplies if necessary.
In a standard 19-inch (EIA310-D) rack, you can install up to six BigIron RX-8 chassis.
For each BigIron RX-8 chassis that you install in a rack, you must provide four standard #12-24
pan-head screws with which to mount and secure the chassis. Before performing this task, you
should have an assembled rack and a #2 Phillips-head screwdriver.
Removing BigIron RX-8 extra shipment screws
The BigIron RX-8 ships with two extra screws installed in the right side of the chassis. These screws
secure the fan tray, protecting it from damage during shipment. You must remove these screws
before installing the chassis.
Figure 25
shows the location of the screws.