Yamaha M7CL M7cl V3 Owner's Manual - Page 131
If you turned on the MIX ON, MIX SEND, existing link group, hold down any [SEL]
![]() |
View all Yamaha M7CL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 131 highlights
3 Use the buttons of the LINK PARAMETER field to select the parameter(s) that will be linked (multiple selections are allowed). The table below lists the parameters you can select in the LINK PARAMETER field. HA button EQ button DYNAMICS 1, 2 button MIX ON button MIX SEND button MATRIX ON button MATRIX SEND button FADER button CH ON button Head amp settings EQ settings (including ATT/HPF) Dynamics 1 and 2 settings On/off status of signals sent to MIX buses Send levels of signals sent to MIX buses On/off status of signals sent to MATRIX buses Send levels of signals sent to MATRIX buses Fader operations [ON] key operations HINT • If you link Dynamic 1 and 2 for two or more input channels, the parameter values will be linked, but the key-in signals are not linked. For more about dynamics, refer to "Using dynamics" (→ p. 118). • If you turn on the EQ button or DYNAMICS 1, 2 button, library recall operations will also be linked. • The HA gain setting and the fader operation will be linked and will maintain the same relative level difference between the channels. 4 If you turned on the MIX ON, MIX SEND, MATRIX ON, or MATRIX send buttons in step 3, use the buttons of the SEND PARAMETER field to specify the bus(es) for which you want operations to be linked (multiple selections are allowed). The table below lists the parameters you can select in the SEND PARAMETER field. MX 1-16 buttons MT 1-8 buttons MIX buses 1-16 MATRIX buses 1-8 NOTE • If nothing is selected in the SEND PARAMETER field, send on/off and send level will not be linked. 5 To link channels, hold down the [SEL] key of the link-source input channel and press the [SEL] key of the link-destination channel. At this time, the values of the parameters you selected in steps 3 and 4 will be copied from the link-source to the link-destination channel. Subsequent operations of the parameters you selected in steps 3 and 4 will be linked between channels belonging to the same link group. The current link status is shown in the channel display field of the window. The Channel Link function HINT • If you want to link three or more channels, hold down the linksource [SEL] key and successively press the [SEL] key of each channel you want to add to the link group. • When you press the [SEL] key of a channel belonging to a link group to make it light, the [SEL] keys of all channels belonging to the same link group will blink. • If you link an INPUT channel to a ST IN channel, parameters that do not exist for a ST IN channel will be ignored. 6 If you want to add a new channel to an existing link group, hold down any [SEL] key within the group and press the [SEL] key that you want to add to the group. HINT • If the link-destination channel is already assigned to another link group, its assignment to the previous group will be cancelled, and it will be added to the newly assigned group. 7 To remove a channel from a link group, hold down any [SEL] key in the same link group, and press the [SEL] key of the channel that you want to remove. HINT • You can also remove all linked channels from the same link group temporarily if you want to edit parameters that are linked to each other while maintaining the same relative level differences, such as the HA gain and fader (for example, if you want to change the level balance between channels that belong to the same link group). While pressing and holding down the [SEL] key for the desired linked channel, change the parameter value. While you are holding down the [SEL] key, the HA gain and fader values will not be linked. (However you cannot temporarily cancel this link during the "fading" phase of the recalled scene.) 11 Grouping and linking M7CL Owner's Manual 131
![](/manual_guide/products/yamaha-m7cl-m7cl-v3-owners-manual-9670c06/131.png)