Yamaha M7CL M7cl V3 Owner's Manual - Page 155

Using the Monitor function 1 SOURCE SELECT field Use the buttons in this field to select the monitor source. This operation can also be performed using the SOURCE SELECT field in the MONITOR screen. B MONITOR FADER level This adjusts the monitor fader level. C FADER ASSIGN MODE button Pressing this button in the MONITOR popup window repeatedly will switch the setting in the following order: NONE → STEREO → MONO → NONE. When STEREO is selected, you can use the SETERO MASTER fader on the top panel to adjust the monitor fader. You can also switch monitor output on and off using the [ON] key located above the STEREO MASTER fader. When MONO is selected, you can use the MONO MASTER fader on the top panel to adjust the monitor fader. You can also switch monitor output on and off by using the [ON] key located above the MONO MASTER fader. D DIMMER field Here you can make settings for the Dimmer function which temporarily attenuates the monitor signal. • DIMMER knob ...........This adjusts the amount by which the monitor signal will be attenuated when the dimmer is on. You can use multifunction encoder 4 to control this. This operation can also be performed in the DIMMER field of the MONITOR screen. • DIMMER ON button ...........If this button is on, the monitor signal level will be attenuated according to the setting of the DIMMER knob. This operation can also be performed in the DIMMER field of the MONITOR screen. E TALKBACK DIMMER field Here you can view and make settings for the Talkback Dimmer. • TALKBACK DIMMER knob ...........This adjusts the amount by which the monitor signal will be attenuated when talkback is on. You can use multifunction encoder 5 to control this. • TALKBACK DIMMER indicator ...........This indicator shows that talkback is on, and that the talkback dimmer is operating. HINT • If the normal dimmer and the talkback are both switched on simultaneously, the setting with the greatest amount of attenuation will be applied. F MONITOR DELAY field This field specifies the monitor delay setting by which the monitor signal is delayed. You can use this in large auditoriums where there is a time difference between the monitor signal and the direct sound. • MONITOR DELAY knob ........... Adjusts the delay time for the monitor signal. You can use multifunction encoder 6 to control this. • MONITOR DELAY ON button ........... If this button is on, the monitor signal will be delayed according to the setting of the MONITOR DELAY knob. G MONO MONITOR button This button allows monaural monitoring. If this button is on, the signal sent from the PHONES OUT jack and the MONITOR OUT L/R channels will be monaural. H PHONES LEVEL LINK button If this is on, the MONITOR LEVEL knob or MONITOR FADER knob will adjust the level of the signal sent to the PHONES OUT jack. I OUTPUT button Switches the monitor function on/off. This operation can also be performed using the OUTPUT button in the MONITOR screen. J Meter field • Output select button ........... This opens the OUTPUT PORT SELECT popup window, where you can select the port that will output the monitor signal. • Level meter ... This indicates the level of the monitor signal. This meter shows the level immediately before the dimmer. K ASSIGN field If you selected DEFINE in the SOURCE SELECT field, use this field to specify the monitor source. You can select up to eight monitor sources simultaneously. Pressing the CLEAR ALL button will clear all selections. 4 Use the buttons of the SOURCE SELECT field to select a monitor source. In the SOURCE SELECT field you can select only one monitor source. However if you've selected DEFINE, you can use the ASSIGN field to specify multiple monitor sources. The following table shows the monitor sources you can select in the SOURCE SELECT field. STEREO L/R button STEREO L/R channel output signal MONO (C) button MONO channel output signal LCR button STEREO L/R + MONO channel (LCR) output signal ST IN 1-4 buttons (M7CL-32/48) ST IN jacks 1-4 input signals OMNI 1-2 - 7-8 buttons OMNI IN jacks 1-8 input signals (M7CL-48ES) DEFINE button The signal(s) selected in the ASSIGN field Monitor/Cue 13 M7CL Owner's Manual 155