Yamaha M7CL M7cl V3 Owner's Manual - Page 80

Signal flow for output channels MIX 1 2 ···1516 M O ST N O MATRIX CUE L R (C) 1 2 ··· 7 8 L R STEREO L,R,MONO(C) To RACKIN PATCH INSERT POIN To OUTPUT PACH STEREO INSERT OUT L,R,MONO (C) POST ON INSERT OUT PRE FADER INSERT OUT PRE EQ INSERT OUT STEREO INSERT IN L,R,MONO (C) PRE EQ METER EQ OUT METER DYNA OUT PRE FADER METER METER GR METER LEVEL BAL CUE ON INSERT ATT 4BAND EQ PRE EQ POST EQ PRE EQ INSERT OUT COMP COMPAND INSERT EXPAND Keyin PRE FADER INSERT OUT PRE FADER Self PRE EQ / Self POST EQ / MIX13-16 OUT / ST (L,R,MONO (C)) POST EQ (PRE FADER) PFL / (POST ON) AFL MATRIX1,3...7 MATRIX2,4...8 LEVEL ON LEVEL ON PRE FADER / POST ON To MATRIX VARI LEVEL ON PAN To MATRIX PRE FADER / POST ON VARI STEREO POST ON METER ON INSERT STEREO OUT L,R,MONO (C) POST ON INSERT OUT POST ON To OUTPUT PATCH To MONITOR SELECT ■ MATRIX channels These channels process the signals sent from MIX channels and STEREO/MONO channels to MATRIX buses, and send them to the corresponding output ports. When the M7CL is in the default state, the following output ports are assigned. • M7CL-32/48 • M7CL-48ES (Daisy Chain) MATRIX channels 1-8 Slot 3 output channels 1-8, 9-16 MATRIX channels 1-6 EtherSound output channels 17-22 MATRIX channels 1/2 OMNI OUT jacks 13/14 MATRIX channels 1-4 OMNI OUT jacks 1-4 MIX 1 2 ···1516 M O ST N O MATRIX CUE L R (C) 1 2 ··· 7 8 L R MATRIX channels 1-8 Slot 3 output channels 1-8, 9-16 MATRIX 1-8 To RACKIN PATCH To OUTPUT PATCH MATRIX INSERT OUT 1-8 INSERT POINT POST ON INSERT OUT PRE FADER INSERT OUT PRE EQ INSERT OUT MATRIX INSERT IN 1-8 PRE EQ METER EQ OUT METER DYNA OUT PRE FADER METER METER GR METER LEVEL CUE ON INSERT ATT 4BAND EQ PRE EQ POST EQ PRE EQ INSERT OUT COMP COMPAND INSERT EXPAND Keyin PRE FADER INSERT OUT PRE FADER Self PRE EQ / Self POST EQ / MIX13-16 OUT/ MATRIX1-8 POST EQ (PRE FADER) PFL / (POST ON) AFL POST ON METER ON INSERT POST ON INSERT OUT MATRIX OUT 1-8 To OUTPUT PATCH To MONITOR SELECT POST ON ● ATT (Attenuator) Attenuates/boosts the level of the signal. ● 4 BAND EQ (4 band equalizer) A parametric EQ with four bands; HIGH, HIGH MID, LOW MID, and LOW. ● DYNAMICS 1 This is a dynamics processor that can be used as a compressor, compander, or expander. ● LEVEL This adjusts the output level of the channel. ● BALANCE (STEREO channel only) Adjusts the left/right volume balance of the STEREO (L/ R) channel. ● ON (On/off) Turns the output channel on/off. If off, that channel is muted. ● MATRIX ON/OFF (MATRIX send on/off) This is an on/off switch for the signal sent from the MIX channels, STEREO (L/R) channel, or MONO (C) channel to each MATRIX bus. ● MATRIX (MATRIX send levels) This adjusts the send level of the signal sent from the MIX channels, STEREO (L/R) channel, or MONO (C) channel to each MATRIX bus. As the position from which the signal is sent to the MATRIX bus, you can choose either, immediately before the fader, or immediately after the [ON] key. 80 M7CL Owner's Manual If the send-destination MATRIX bus is set to stereo, you can use the PAN knob to adjust the panning between the two MATRIX buses. If the send-source is a stereo MIX channel or the STEREO channel, use the BALANCE knob to adjust the volume balance of the left and right channels sent to the two MATRIX buses. ● INSERT You can patch the desired output/input ports to insert an external device such as an effect processor. You can switch the insert-out and insert-in locations. ● METER This meters the level of the output channel. You can switch the position at which the level is detected. ● KEY IN (MIX channels 13-16 only) You can send the output signals of MIX channels 13-16 to dynamics processors and use them as key-in signals to control the dynamics. ● RACK IN PATCH This patches the output signal of the output channel to an input of the rack. ● OUTPUT PATCH This assigns an output port to an output channel. ● MONITOR SELECT This selects the output signal of an output channel as a monitor source.