Yamaha M7CL M7cl V3 Owner's Manual - Page 156
Make settings for Dimmer, Delay, and Mon, STREO MASTER fader/MONO MASTER
View all Yamaha M7CL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 156 highlights
Using the Monitor function If you've selected DEFINE in the SOURCE SELECT field, you can use the ASSIGN field to select multiple sources. The following table shows the monitor sources you can select in the ASSIGN field. MIX 1-16 buttons Output signals of MIX channels 1-16 MTRX 1-8 buttons Output signals of MATRIX channels 1-8 STEREO L/R button STEREO L/R channel output signal MONO (C) button MONO channel output signal ST IN 1-4 buttons (M7CL-32/48) ST IN jacks 1-4 input signals OMNI 1-2 - 7-8 buttons OMNI IN jacks 1-8 input signals (M7CL-48ES) NOTE • You can select a maximum of eight monitor sources in the ASSIGN field. If you select eight monitor sources, no further selections will be possible. Please turn off the buttons for unneeded sources. 5 To specify a port as the output destination for monitor signals L, C, R, press one of the output select buttons (L/R/C) in the meter field to open the OUTPUT PORT SELECT popup window, and choose from the following monitor signal output destinations (multiple selections are allowed). • M7CL-32/48 OMNI 1-16 2TR OUT L, R SLOT 1-3 OMNI OUT jacks 1-16 2TR OUT DIGITAL jack L, R Output channels 1-16 of an I/O card installed in slots 1-3 • M7CL-48ES ES 1-24 2TR OUT L, R OMNI 1-8 SLOT 1-3 EtherSound output channels 1-24 2TR OUT DIGITAL jack L, R OMNI OUT jacks 1-8 Output channels 1-16 of an I/O card installed in slots 1-3 When you've selected an output port, press the CLOSE button to close the popup window. In the same way, specify the output ports for MONITOR OUT L, R, and C. HINT • If desired, you can specify output ports only for MONITOR OUT L and R, and monitor through two speakers. • If you have not specified an output port for MONITOR OUT C, selecting the MONO (C) button or LCR button as the monitor source will automatically cause the MONO channel signal to be distributed to MONITOR OUT L/R. 6 To enable monitoring, press the OUTPUT button to turn it on. The monitor source you selected in step 4 will be sent to the output destination you specified in step 5. HINT • The PHONES OUT jack will always output the monitor signal, regardless of whether the OUTPUT button is on or off. 7 To adjust the monitor fader by using the STREO MASTER fader/MONO MASTER fader, press the FADER ASSIGN MODE button to select STERO or MONO. When STEREO is selected, you can use the SETERO MASTER fader on the top panel to adjust the monitor fader. When MONO is selected, you can use the MONO MASTER fader on the top panel to adjust the monitor fader. Depending on the FADER ASSIGN MODE setting, the MONITOR button in the function access area turns red when STEREO is selected, and the button turns yellow when MONO is selected. NOTE • The monitor fader and the MONITOR LEVEL knob are placed in serial. The MONITOR LEVEL knob on the top panel remains effective while you are using this function to change the monitor level. If the MONITOR LEVEL knob is set to minimum, no monitor signal will be output. 8 Adjust the monitor fader using the STEREO MASTER fader/MONO MASTER fader, or the MONITOR FADER knob on the screen. NOTE • The [ON] keys for the STEREO or MONO channels and the OUTPUT buttons on the MONITOR screen are linked. The PHONES OUT jack will always output the monitor signal, regardless of whether the OUTPUT button is on or off. 9 To adjust the monitor level, use the MONITOR LEVEL knob located in the SCENE MEMORY/MONITOR section of the top panel. If PHONES LEVEL LINK is ON, use the MONITOR LEVEL knob and the monitor fader, as well as the PHONES LEVEL knob to adjust the monitor level when monitoring through headphones. 10 Make settings for Dimmer, Delay, and Monaural as desired. HINT • Monitor on/off operations, selection of the monitor source, and dimmer on/off operations can also be assigned to userdefined keys (→ p. 216). 156 M7CL Owner's Manual