Brother International LT2-B845 MKII Instruction Manual - Multi - Page 57
Switching, upper, lower, Umschalten, Untertransport, Unter, Obertransport
View all Brother International LT2-B845 MKII manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 57 highlights
9. SWITCHING BETWEEN UPPER FEED AND LOWER FEED [B842-1C] 9. UMSCHALTEN ZWISCHEN OBER-UND UNTERTRANSPORT [B842-1C] 9. COMMUTATION ENTRE ENTRAINEMENT SUPERIEUR ET ENTRAINEMENT INFERIEUR [B842-1C] 9. CAMBIO ENTRE ALIMENTACION SUPERIOR E INFERIOR [B842-1C] ■ Switching from upper feed to lower feed 1. Remove the presser foot, needle plate and feed dog. 2. Loosen the screw 0 of the needle bar rocking crank assembly, move the needle bar rocking link 0 from the highest position to the lowest position, and then tighten the screw 0. 3. Loosen the screw 0 of timing pulley D, remove the cone-pointed screw 0, turn the lower shaft 0 so that the groove moves from position A to position B, and then tighten the screw 0 and the screw 0. 4. Loosen the screws 0 of the left and right pinion gears. 5. Raise the needle bar 2 mm from its lowest position. 6. Align the tip of the rotary hook with the center of the needle, and then tighten the screws 0 of the pinion gear. Push the rotary hook down while tightening the screws 0. 7. Provisionally install the feed dog (for lower feed). Move the needle bar to the lowest position, check that the needle down position is correct, and then securely tighten the feed dog into place. 8. Install the needle plate (for lower feed). Be careful of the rotary hook holder when installing. 9. Adjust so that the clearance between the opener and the rotary hook is 0.1-0.2 mm. 10. Install the presser foot. ■ Switching from lower feed to upper feed 1. Remove the presser foot, needle plate and feed dog. 2. Loosen the screw 0 of the needle bar rocking crank assembly, move the needle bar rocking link 0 from the lowest position to the highest position, and then tighten the screw 0. 3. Loosen the screw 0 of timing pulley D, remove the cone-pointed screw 0, turn the lower shaft 0 so that the groove moves from position B to position A, and then tighten the screw 0 and the screw 0. 4. Set the feed regulator dial to . 5. Loosen the screws 0 of the left and right pinion gears. 6. Raise the needle bar 2.4 mm from its lowest position. 7. Align the tip of the rotary hook with the center of the needle, and then tighten the screws 0 of the pinion gear. Push the rotary hook down while tightening the screws 0. 8. Provisionally install the feed dog (for upper feed). Move the needle bar to the lowest position, check that the needle down position is correct, and then securely tighten the feed dog into place. 9. Install the needle plate (for upper feed). Be careful of the rotary hook holder when installing. 10. Adjust so that the clearance between the opener and the rotary hook is 0.1-0.2 mm. 11. Install the presser foot. ■ Umschalten vom Ober- auf den Untertransport 1. Nehmen Sie den StoffdruckerfuR, die Stichplatte und den Transporteur ab. 2. Losen Sie die Schraube 0 des Nadelstangenkipphebels, schieben Sie das Glied 0 von der h6chsten in die tiefste Position und ziehen Sie die Schraube 0 wieder fest. 3. L6sen Sie die Schraube 0 der Steuerscheibe D, entfernen Sie die Konusschraube 0 und drehen Sie die untere Welle 0, um die Nut von der Position A auf die Position B zu stellen und ziehen Sie danach die Konusschraube 0 und die Schraube 0 wieder fest. 4. Losen Sie die Schrauben 0 des linken und rechten Ritzels. 5. Heben Sie die Nadelstange von der tiefsten Position urn 2 mm an. 6. Richten Sie die Drehgreiferspitze auf die Nadelmitte aus und ziehen Sie die Schrauben 0 des Ritzels fest. Dr0cken Sie beim Festziehen der Schrauben 0 das Ritzel nach unten. 7. Bringen Sie den Transporteur (fur Untertransport) provisorisch an. Senken Sie die Nadelstange in die tiefste Position ab, kontrollieren Sie, ob die untere Nadelposition richtig ist und ziehen Sie den Transporteur richtig fest. 8. Montieren Sie die Stichplatte fur den Untertransport. Passen Sie dabei besonders auf den Drehgreiferhalter auf. 9. Stellen Sie den Abstand zwischen dem Offner und dem Drehgreifer auf 0,1-0,2 mm ein. 10. Bringen Sie den Stoffdruckerfuf3 an. ■ Umschalten vom Unter- auf den Obertransport 1. Nehmen Sie den StoffdruckerfuB, die Stichplatte und den Transporteur ab. 2. L0sen Sie die Schraube 0 des Nadelstangenkipphebels, schieben Sie das Glied 0 von der tiefsten in die hochste Position und ziehen Sie die Schraube 0 wieder fest. 3. L6sen Sie die Schraube 0 der Steuerscheibe D, entfernen Sie die Konusschraube 0 und drehen Sie die untere Welle 0, um die Nut von der Position B auf die Position A zu stellen und ziehen Sie danach die Konusschraube 0 und die Schraube 0 wieder fest. 4. Stellen Sie die Transporteinstellscheibe auf . 5. L6sen Sie die Schrauben 0 des linken und rechten Ritzels. 6. Heben Sie die Nadelstange von der tiefsten Position urn 2,4 mm an. 7. Richten Sie die Drehgreiferspitze auf die Nadelmitte aus und ziehen Sie die Schrauben 0 des Ritzels fest. Dr0cken Sie beim Festziehen der Schrauben 0 das Ritzel nach unten. 8. Bringen Sie den Transporteur (fur Obertransport) provisorisch an. Senken Sie die Nadelstange in die tiefste Position ab, kontrollieren Sie, ob die untere Nadelposition richtig ist und ziehen Sie den Transporteur richtig fest. 9. Montieren Sie die Stichplatte fur den Obertransport. Passen Sie dabei besonders auf den Drehgreiferhalter auf. 10. Stellen Sie den Abstand zwischen dem Offner und dem Drehgreifer auf 0,1-0,2 mm ein. 11. Bringen Sie den Stoffdruckerfug an. - 42 - Model No. LT2-6840 Mark II LT2-B870 Mark II