D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide
D-Link DWS-3160-24TC Manual
View all D-Link DWS-3160-24TC manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DWS-3160-24TC manual content summary:
- D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 1
Fdo - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 2
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Information in this document is subject to change without notice. © 2011 D-Link Corporation. All rights reserved. Reproduction of this document in any manner whatsoever without the written permission of D-Link Corporation is - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 3
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Table of Contents Intended Readers...1 Typographical Conventions...1 Notes, Notices and Cautions...1 Section 1 Web-based Switch Configuration 2 Chapter 1 Introduction ...2 Chapter 2 Login to the Web Manager ...2 Chapter 3 Web- - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 4
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide IPv4 Static/Default Route Settings ...126 IPv4 Route Table...127 IPv6 Static/Default Route Settings ...127 IP Forwarding Table ...128 VRRP ...128 Chapter 5 QoS ...133 802.1p Settings...134 Bandwidth Control ...136 Traffic Control - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 5
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Mirror ...303 sFlow ...305 Ping Test...308 Trace Route ...309 Peripheral ...310 Chapter 11 Save and Tools ...311 Section 3 WLAN ...312 Chapter 1 Security ...312 Captive - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 6
Instructions General Precautions for Rack-Mountable Products Protecting Against Electrostatic Discharge The DWS-3160 Series Web UI Reference Guide contains information for setup and management of the Switch. This manual to avoid the problem. A CAUTION indicates a potential for property damage, personal injury, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 7
Switch Web UI Reference Guide Section 1 Web-based Switch Configuration Introduction Login to the Web Manager Web-based User Interface Web Pages Chapter 1 Introduction All software functions of the DWS-3160 Series switches represent the IP address of the Switch. NOTE: The factory default IP address is - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 8
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-1 Enter Network Password window Leave both the User Name field and the Password field blank and click OK. This will open the Web-based user interface. The Switch management features available in the web-based manager are - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 9
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide AREA 2 AREA 1 AREA 3 Area Number Area 1 Area 2 panel of the Switch. This area displays the Switch's ports, console and management port, showing port activity. Click the D-Link logo to go to the D-Link website. Some management - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 10
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide L2 Features - In this section the user will be able to configure features regarding the Layer 2 functionality of the Switch regarding the wireless Quality of Service functionality of the Switch. Network Visualization - In this - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 11
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Section 2 LAN This section describes all the available the DWS-3160 Series link. The Device Information window shows the Switch's MAC Address (assigned by the factory and unchangeable), the Boot PROM Version, Firmware Version, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 12
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide System Information Settings The user can enter a System Name, System Location, and System Contact to aid in defining the Switch. To view the following window, click System Configuration > System Information Settings, as show - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 13
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 5-3 Port Settings window To configure switch ports: 1. Choose the port Full_Master, 1000M Full_Slave, and 1000M Full. Gigabit connections only support full duplex connections and take on certain characteristics that are - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 14
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide from a data stream received from the master. If one connection is set for 1000M Full_Master, the other side of the connection must be set for 1000M Full_Slave. Any other configuration will result in a link down status for both - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 15
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Switch supports jumbo frames. Jumbo frames are Ethernet frames with more than 1,518 bytes of payload. The Switch supports or disable the Jumbo Frame function on the Switch. The default is Disabled. When disabled, the maximum - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 16
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide PoE The DWS-3160-24PC switches support Power over Ethernet (PoE) as defined by the IEEE 802.3af and 802.3at. All ports can support 6. The Switches work with all D-Link 802.3af capable devices. The Switch includes the following - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 17
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 5-7 PoE System Settings window The following parameters can be configured: Parameter Description Power Limit (37760) Sets the limit of power to be used from the Switch's power source to PoE ports. The user may - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 18
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 5-8 PoE Port Settings window The following parameters can be configured: Parameter Description From Port / To Port State Time Range Priority Power Limit Select a range - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 19
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click Apply to implement changes made. as defined. Choose from the following options: 2, 5, 10, 15 minutes or Never. The default setting is 10 minutes. Data Bits Display the data bits used for the serial port connection. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 20
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide temperature setting. High Threshold Enter Users who choose this method will only save log files when they manually tell the Switch to do so, either using the Save Log link in the Save folder. Time Interval - Users who choose this - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 21
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 5-12 System Log Server Settings (514 or 6000-65535) Type the UDP port number used for sending Syslog messages. The default is 514. Status Choose Enabled or Disabled to activate or deactivate. Click the Apply button to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 22
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide - When selecting Module List, the module name must be manually entered. Available modules are MSTP, ERROR_LOG, CFM_EXT, and below: Parameter Description Interface Name Enter the IP interface name used. IPv4 Address Enter the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 23
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide To view the following window, click System Configuration than 32 alphanumeric characters that will be used to identify this time range on the Switch. This range name will be used in the Access Profile table to identify the access - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 24
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Weekdays Use the check boxes to button to remove the specific entry. Time Settings Users can configure the time settings for the Switch. To view the following window, click System Configuration > Time Settings, as show below: - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 25
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide User Accounts Settings The Switch allows the control of user privileges. To /Write Network Monitoring Community Strings and Trap Stations Update Firmware and Configuration Files System Utilities Factory Reset User Account - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 26
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Command Logging Settings This window is used to the function. Click the Apply button to accept the changes made. NOTE: When the switch is under the booting procedure, all configuration commands will not be logged. When the user - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 27
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 2 Management ARP Gratuitous ARP IPv6 Neighbor Settings IP Interface Management Settings Session Table Single IP age-out time, in minutes. The default is 20 minutes. IP Address The IP address of the ARP entry. MAC - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 28
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The host, usually a layer 3 switch, will respond to packets destined for configure the specific entry and select the proxy ARP state of the IP interface. By default, both the Proxy ARP State and Local Proxy ARP State are disabled. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 29
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Gratuitous ARP Global Settings The user can enable The gratuitous ARP packet is sent by a source IP address that is identical to the IP that the packet is queries for. By default, the state is Disabled status. Click the Apply - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 30
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 6-5 Gratuitous ARP Settings window The fields that can be configured are described below: Parameter Description Trap Use the drop-down menu to enable or disable the trap option. By default the trap is disabled. Log - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 31
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 6-6 IPv6 Neighbor Settings window The fields that can be configured are described below: Parameter Description Interface Name Enter the interface name of the IPv6 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 32
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide To view the following window, click Management > IP Interface > System IP Address Settings, as show below: Figure 6-7 System IP the entry of an IP address, subnet mask, and a default gateway for the Switch. These fields should be - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 33
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide current subnet should be sent. This is usually the address of a router or a host acting as an IP gateway. If your network is not part of an intranet, or you do not want the Switch to be accessible outside your local network, you - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 34
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide VLAN Name Enter the VLAN Name used. as a Secondary Interface. When the primary IP is not available, the VLAN will switch to the secondary interface. It will switch back when the primary IP was recovered. Click the Apply button - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 35
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide can enter the neighbor's global or local link address. NS Retransmit Time (0- Enter the instructions. The user may also consult the Upload Log File window description located in the Tools section of this manual. If the Switch - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 36
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 6-13 Management Settings default. To disable it, click the Disabled radio button. DHCP Auto Configuration State Enable or disable the Switch's DHCP auto configuration feature. When enabled, the Switch is instructed - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 37
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Refresh button to refresh the display table so that new entries will appear. Single IP Management Simply put, D-Link Single IP Management is a concept that will stack switches together over Ethernet instead of using - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 38
operate as the CS of a SIM group, additional DWS-3160 Series switches may join the group by manually configuring the Switch to be a MS. The CS will then serve as the in band entry point for access to the MS. The CS's IP address will become the path to all MS's of the group and the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 39
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide To view the following window, click Management > Single IP Management > Single IP Settings, as show below: Figure 6-15 Single IP Settings window The fields that can be configured are described below: Parameter Description - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 40
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 6-16 Single IP Management window - Tree View The Topology window holds the following information on the Data tab: Parameter Description Device Name This field will display the Device Name of the switches in the SIM - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 41
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 6-17 Topology view This window will display how the devices within the Single IP Management Group connect to other groups and devices. Possible icons on this window are as follows: Icon Description Group Icon - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 42
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 6-18 Device Information Utilizing the Tool Tip Setting the mouse cursor over a line between two devices will display the connection speed between the two - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 43
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 6-20 Right-Clicking a Group Icon The be given the name default and tagged with the last six digits of the MAC Address to identify it. Module Name Displays the full module name of the switch that was right-clicked - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 44
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 6-22 Right-clicking a Commander Icon the following dialog box for the user to enter a password for authentication from the Candidate Switch before being added to the SIM group. Click OK to enter the password or Cancel to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 45
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide • Property - To pop up a window to display the device information. Menu Bar The Single IP About window Firmware Upgrade This screen is used to upgrade firmware from the Commander Switch to the Member Switch. Member Switches will - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 46
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide To view the following window, click Management > Single IP Management > Firmware Upgrade, as show below: Figure 6-29 Firmware potential problems in the Switch, switch group or network. Managed devices that support SNMP include - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 47
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide information controlled by the on-board SNMP agent. SNMP defines both the format of the MIB specifications and the protocol used to access this information over the network. The Switch supports the SNMP versions 1, 2c, and 3. The - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 48
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide and disable the SNMP trap support function of the switch and SNMP authentication failure trap support, respectively. To view Traps Enable this option to use the SNMP Link Change Traps feature. Coldstart Traps Enable this option - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 49
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 6-34 SNMP Linkchange Traps Settings window The fields that can be configured are described below: Parameter Description From Port / To Port Select the starting - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 50
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description View Name Type an community string: • An Access List of IP addresses of SNMP managers that are permitted to use the community string to gain access to the Switch's SNMP agent. • Any MIB view that - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 51
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide SNMP Group Table Settings An SNMP Group created with the Switch's SNMP agent. User-based Security Model SNMPv1 - Specify that SNMP version 1 will be used. SNMPv2 - Specify that SNMP version 2c will be used. The SNMPv2 supports - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 52
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide To view the following default value is suggested in RFC2271. The very first bit is 1, and the first four octets are set to the binary equivalent of the agent's SNMP management private enterprise number as assigned by IANA (D-Link - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 53
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide has been checked. This field will require the below: Parameter Description Host IP Address Type the IP address of the remote management station that will serve as the SNMP host for the Switch. User-based Security Model - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 54
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide To view the following window, click Management > (RMON) for the rising and falling alarm trap feature for the SNMP function on the Switch. To view the following window, click Management > SNMP Settings > RMON Settings, as show - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 55
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide RMON Falling Alarm Trap Enable this option to use the RMON Falling Alarm Trap Feature. Click the Apply button to accept the changes made. Telnet Settings Users can configure Telnet Settings on the Switch Enabled by default. If you - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 56
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 3 VLAN QinQ Spanning Tree Link Aggregation FDB L2 Multicast of data may be transmitted simultaneously. It is intended to alleviate problems associated with the delivery of time critical data over congested networks. The - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 57
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide a routing function between the VLANs. • The Switch supports IEEE 802.1Q VLANs. The port untagging function -unaware. • The Switch's default is to assign all ports to a single 802.1Q VLAN named "default." • The "default" VLAN has a - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 58
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The main characteristics of IEEE 802.1Q are as after the MAC source address, but before the original EtherType/Length or Logical Link Control. Because the packet is now a bit longer than it was originally, the Cyclic - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 59
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-3 Adding an IEEE 802.1Q ports are also assigned a PVID, for use within the Switch. If no VLANs are defined on the Switch, all ports are then assigned to a default VLAN with a PVID equal to 1. Untagged packets are assigned - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 60
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Switch to the "default." As new VLANs are configured in Port-based mode, their respective member ports are removed from the "default." Packets cannot cross VLANs. If a member of one VLAN wants to connect to another VLAN, the link - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 61
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide On port-based VLANs, NICs member of VLAN 2. If the destination lies on another port (found through a normal forwarding table lookup), the Switch then looks to see if the other port (Port 10) is a member of VLAN 2 (and can - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 62
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-5 802.1Q VLAN Settings - Add the VLAN name in the Add/Edit VLAN tab. Advertisement Enable this function to allow the Switch sending out GVRP packets to outside sources, notifying that they may join the existing VLAN. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 63
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-6 802.1Q VLAN Settings - Find VLAN ID List that can be added, deleted or configured. Enabling this function will allow the Switch to send out GVRP packets to outside sources, notifying that they may join the existing - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 64
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide the port as forbidden. Click the Apply button to accept the changes made. NOTE: The Switch supports is a 2-octet IEEE 802.2 Link Service Access Point (LSAP) pair. The first octet is for Destination Service Access Point (DSAP) and - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 65
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide want to re-write the 802.1p default priority previously set in the Switch, which is used to determine the CoS Switch. For more information on priority queues, CoS queues and mapping for 802.1p, see the QoS section of this manual - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 66
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Delete All button to remove type of configuration might be required, would be if the client was on a distinct IP subnet, or if there was some confidentiality-related need to segregate traffic between the clients. To - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 67
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Leave Time (100-100000) Enter the Leave Time value in milliseconds. Leave All Time (100100000) Enter the Leave All Time value in milliseconds. NNI BPDU Address Used to determine the BPDU protocol address for GVRP in service - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 68
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide GVRP The GARP VLAN Registration Protocol (GVRP) enables the port to dynamically become a member of a VLAN. GVRP is Disabled by default from this user will be able to be serviced under the specified VLAN. To view the following - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 69
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide port of the primary VLAN will behave as the tagged member of the secondary VLAN. A secondary VLAN cannot be specified with advertisement. Only the primary - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 70
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Community. Secondary VLAN Name Enter a secondary the View Private VLAN List link to view all the private VLAN. PVID Auto Assign Settings Users can enable or disable PVID Auto Assign Status. The default setting is enabled. To view - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 71
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Voice VLAN Name The name of the voice VLAN. Voice VID (1-4094) The VLAN ID of the voice VLAN. Priority The priority of the voice VLAN, the range is 0 - 7. The default priority is 5. Aging Time (1-65535) The aging time to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 72
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide This page is used to configure and B. Without a VLAN Trunk, you must first configure VLAN groups 1 and 2 on all intermediary switches C, D and E; otherwise they will drop frames with unknown VLAN group tags. However, with VLAN - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 73
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Refer to the following figure for an illustrated made for each individual section. Browse VLAN Users can display the VLAN status for each of the Switch's ports viewed by VLAN. Enter a VID (VLAN ID) in the field at the top of - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 74
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide greatly expanding the VLAN network and enabling greater support of customers utilizing multiple VLANs on the network. IEEE 802.1Q VLANs which we will call SPVIDs (Service Provider VLAN IDs). These VLANs are marked by a TPID - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 75
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-25 QinQ example window In this example, the Service Provider Access Network switch (Provider edge switch operate when the switch is in Double VLAN mode: • Guest VLANs. • Web-based Access Control. • IP Multicast Routing. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 76
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide QinQ Settings This window is used to configure the Q-in Add Inner Tag Specifies that an Inner Tag will be added to the entry. By default the Disabled option is selected. Click the Apply button to accept the changes made for - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 77
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide to remove a specific entry. Spanning Tree This Switch supports three versions of the Spanning Tree Protocol: 802.1D MSTP have been recently introduced to D-Link managed Ethernet switches, a brief introduction to the technology - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 78
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Each switch utilizing the MSTP on a network will have a the possible 4094 VLANs supported by the Switch for a given instance. To utilize the MSTP function on the Switch, three steps need to be taken: 1. The Switch must be set to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 79
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide the topology to stabilize before transitioning , all ports operating in full-duplex mode are considered to be P2P ports, unless manually overridden through configuration. 802.1D-1998/802.1D-2004/802.1Q-2005 Compatibility MSTP or - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 80
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide MSTP - Select this parameter to set the Multiple Spanning Tree Protocol (MSTP) globally on the Switch. Forwarding BPDU This field can be Enabled or Disabled. When Enabled, it allows the forwarding of STP BPDU packets from - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 81
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-29 STP Port Settings window The fields that can be configured are described below: Parameter Description From Port / To Port External Cost (0=Auto) P2P - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 82
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide will never be selected to be the Root port. The default is False. Click the Apply button to accept the changes VID range from configured VLANs set on the Switch. Supported VIDs on the Switch range from ID number 1 to 4094. Click - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 83
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide To view the following window, click L2 a value between 0 and 15. An entry of 0 in this field denotes the CIST (default MSTI). This parameter is set to represent the relative cost of forwarding packets to specified ports when - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 84
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide occurs. A lower Internal cost represents a Link Aggregation Understanding Port Trunk Groups Port trunk groups are used to combine a number of ports together to make a single high-bandwidth data pipeline. The Switch supports - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 85
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide All of the ports in the group must be members of the same VLAN, and their STP status, static multicast, traffic control; traffic segmentation and 802.1p default priority configurations must be identical. Port locking, port - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 86
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide frames. To view the following window, click L2 Features > Link Aggregation > LACP Port Settings, as show below: Figure 7-35 LACP ports as active. Both devices must support LACP. Passive - LACP ports that are designated as passive cannot - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 87
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide FDB Static FDB Settings Unicast Static FDB Settings Users can set up static unicast forwarding on the Switch "port number" (e.g. 5). When only entering port number, the default unit ID is 1. Click the Apply button to accept the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 88
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-37 Multicast Static FDB Settings window The fields that can be configured are described below: Parameter Description VID The VLAN ID of the VLAN - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 89
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-38 MAC Notification Settings window The fields that can be configured are described below: Parameter Description State Enable or disable MAC notification globally on the Switch Interval (1-2147483647) The time in - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 90
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Time (10-1000000) forwarding table default setting is 300 seconds. Click the Apply button to accept the changes made. MAC Address Table This allows the Switch's MAC address forwarding table to be viewed. When the Switch - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 91
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-41 ARP & FDB Table window specific entry based on the MAC address entered. Click the Find by IP Address button to locate a specific entry based on the IP address entered. Click the View All Entries button to display all - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 92
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameters Settings. Click the Modify Router Port link to configure the IGMP Snooping Router Port Settings used in calculating the following IGMP message intervals: By default, the robustness variable is set to 2. Specify the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 93
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Fast Leave Enable or disable the IGMP snooping fast leave function. If enabled, the membership is immediately removed when the system receive the IGMP leave message. State If the state is enable, it allows the switch link, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 94
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Clear All button to unselect all Static Group Settings Users can view the Switch's IGMP Snooping Group Table. IGMP Snooping allows the Switch to read the Multicast Group IP address and the corresponding MAC address from - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 95
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The fields that can be configured are made and return to the previous window. IGMP Router Port Users can display which of the Switch's ports are currently configured as router ports. A router port configured by a user (using - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 96
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide NOTE: The abbreviations used on this page are Static Router Port (S), Dynamic Router Port (D) and Forbidden Router Port (F). IGMP Snooping Group Users can view the Switch's IGMP Snooping Group Table. IGMP Snooping allows the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 97
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-50 IGMP Snooping Forwarding Table window The fields that can button to display all the existing entries. Click the Packet Statistics link to view the IGMP Snooping Counter Table. After clicking the Packet Statistics - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 98
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-52 Browse IGMP Snooping Counter window Click the Clear Counter button to clear all the information displayed in the fields. Click the Refresh button - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 99
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide this message is sent by the router to ask if any link is requesting multicast data. There are two types of MLD to a Layer 2 switch that is recording and sending IP multicast data. The switch needs to forward IP data to a data - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 100
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide for a specific entry. Click the Modify Router Port link to configure the MLD Snooping Router Port Settings for The default setting is 125 seconds. The maximum time in seconds to wait for reports from listeners. The default setting - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 101
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide for the specified VLAN. This field is Disabled by default. Report Suppression Use the drop-down menu to enable the previous window. After clicking the Modify Router Port link, the following page will appear: Figure 7-56 MLD - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 102
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Forbidden Router Port This section is List value here. Rate Limit (1-1000) Configure the rate limit of MLD control packet that the switch can process on a specific port/VLAN. The rate is specified in packet per second. The - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 103
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-58 MLD Snooping Static Group made and return to the previous window. MLD Router Port Users can display which of the Switch's ports are currently configured as router ports in IPv6. A router port configured by a user - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 104
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-60 MLD Router Port window Parameter Router Port (F). MLD Snooping Group Users can view MLD Snooping Groups present on the Switch. MLD Snooping is an IPv6 function comparable to IGMP Snooping for IPv4. To view - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 105
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Clear All Data Driven button to delete all MLD snooping groups which is learned by the Data Driven feature of specified VLANs. MLD Snooping Forwarding Table This page displays the switch received by the switch since MLD - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 106
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Port List Specify a list of ports to be entries. Click the Packet Statistics link to view the MLD Snooping Counter Settings for the specific entry. After clicking the Packet Statistics link, the following page will appear: - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 107
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Find button to locate a specific entry based on the information entered. Click the View All button to display all the existing entries. Multicast VLAN In a switching ISM VLAN. 6. One IP multicast address cannot be added - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 108
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Find button to locate a specific entry based Group Profile Address Settings for the specific entry. After clicking the Group List link, the following page will appear: Figure 7-67 Multicast Group Profile Multicast - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 109
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide forwarded on the multicast VLAN. None - If this is specified, the packet's original priority is used. The default setting is None. Replace Priority Specify that the packet's priority will be changed by the switch List link to IP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 110
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Select All button to select discard the changes made and return to the previous window. After clicking the Profile List link, the following page will appear: Figure 7-70 IGMP Snooping Multicast VLAN Group List Settings - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 111
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-72 Multicast Group Profile priority will be used. The default setting is None. Replace Priority Tick the check box to specify that the packet's priority will be changed by the switch, based on the remap priority. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 112
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Edit button to configure the MLD Snooping Multicast VLAN Settings for the specific entry. Click the Delete button to remove the specific entry. Click the Profile List link to configure the MLD Snooping Multicast VLAN - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 113
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide 1 and 24. Profile Name Enter a name for the IP Multicast Profile. Click the Add button to add a new to remove all the entries listed. Click the Group List link to configure the multicast address group list settings for the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 114
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Delete button to remove the specific entry. After clicking the Group List link, the following page will appear: Figure 7-77 Multicast Address Group List Settings window The fields that can be configured are described - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 115
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Delete button to remove the specific multiple pages exist. IPv4 Max Multicast Group Settings Users can configure the ports and VLANs on the switch that will be a part of the maximum filter group, up to a maximum of 1024. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 116
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-80 IPv4 Multicast Profile Settings window The fields that can be configured are described below: Parameter Description Profile ID (1-24) Enter a Profile ID between 1 and 24. Profile Name Enter a name for the IP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 117
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-82 IPv6 Limited Multicast Range pages exist. IPv6 Max Multicast Group Settings Users can configure the ports and VLANs on the switch that will be a part of the maximum filter group, up to a maximum of 1024. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 118
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide This will instruct the Switch to forward Link). When the failure happens, protection switching blocks the failed link and unblocks the RPL. When the failure clears, protection switching blocks the RPL again and unblocks the link - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 119
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide RPL (Ring Protection Link) - Link designated by mechanism Protected VLAN - The service traffic VLANs for transmission of normal network traffic This page is used to enable the ERPS function on the switch. NOTE: STP and LBD - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 120
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-86 ERPS Settings - Detail Information window Click on the Edit button to re-configure the specific entry. Click on the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 121
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Specifies the guard time of the R-APS function. The default guard time is 500 milliseconds. WTR Time (5-12) previous window. After clicking the Sub-Ring Information link, the following window will appear: Figure 7-88 ERPS - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 122
LLDP DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide LLDP Global Settings On this page the user can configure for an advertisement expires the advertised data is then deleted from the neighbor Switch's MIB. LLDP ReInit Delay (1-10) The LLDP re-initialization delay interval - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 123
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide LLDP Port Settings On this page the user can neither transmit nor receive LLDP frames. The default value is TX And RX. Subtype Use the drop-down menu to select the type of the IP address information will be sent. Action Use - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 124
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide LLDP Management Address List On this page . Address Enter the management IP address or the IP address of the entity you wish to advertise to. The IPv4 address is a management IP address, so the IP information will be sent with - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 125
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-92 LLDP Basic TLVs Settings window The fields that can be configured are described below: Parameter Description From Port / To Port Select the port - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 126
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-93 LLDP Dot1 TLVs Settings window The fields that can be configured are described below: Parameter Description From Port / To Port Use the drop- - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 127
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide supports the auto-negotiation function, whether the function is enabled, whether it has auto-negotiated advertised capability, and what is the operational MAU type. The default state is Disabled. Link Aggregation The Link - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 128
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-95 LLDP Statistics System window The fields that can be configured are described below: Parameter Description Port Use the drop-down menu to select a - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 129
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 7-97 LLDP Local Port Information LLDP Remote Port Information This page displays port information learned from the neighbors. The switch receives packets from a remote station but is able to store the information as local - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 130
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Port Use the drop-down menu to select a Switch supports Network Load Balancing (NLB). This is a MAC forwarding control for supporting the Microsoft server load balancing application where multiple servers can share the same IP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 131
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 4 L3 Features IPv4 Static/Default Route Settings IPv4 Route Table IPv6 Static/Default Route Settings IPv6 Route Table IP Forwarding Table VRRP IPv4 Static/Default Route Settings The Switch supports static routing for IPv4 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 132
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide IPv4 Route Table The IP routing table stores all the external routes information of the Switch. This window is used to display all the external route information on the switch. To view the following window, click L3 Features > - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 133
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide backup routes according to the IP address associated with a virtual router is called the Master. The Master forwards packets sent to this IP address. This allows any Virtual Router IP address on the LAN to be used as the default - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 134
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide VRRP Global Settings This window is used to be different from other VRRP groups set on the Switch. Enter the virtual router's IP address. This IP address is also the default gateway that will be statically assigned to end hosts - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 135
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Interval (1-255) Preempt Mode Use the must be different from other VRRP groups set on the Switch. Enter the virtual router's IP address. This IP address is also the default gateway that will be statically assigned to end hosts - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 136
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Advertisement Interval (1-255) Enter the interval be consistent with all routers participating within the same VRRP group. Critical IP Address Enter an IP address of the physical device that provides the most direct route to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 137
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 8-10 VRRP Authentication Settings - the two passwords are not exactly the same, the packet will be dropped. IP - Specify to set an IP for authentication in comparing VRRP messages received by the router. If the two values - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 138
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 5 QoS 802.1p Settings Bandwidth Control Traffic Control Settings DSCP HOL Blocking Prevention Scheduling Settings The Switch supports 802.1p priority queuing Quality of Service. The following section discusses the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 139
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Understanding QoS The Switch supports 802.1p priority queuing. The Switch has eight priority queues. These priority queues are numbered from 7 (Class 7) - the highest priority queue - to 0 (Class 0) - the lowest priority queue. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 140
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 9-2 Default Priority Settings window button to accept the changes made. 802.1p User Priority Settings The Switch allows the assignment of a class of service to each of the 802.1p priorities. To view the following window, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 141
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Bandwidth Control The bandwidth control settings are used to place a ceiling on the transmitting and receiving data rates for any selected port. Bandwidth Control Settings - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 142
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Effective TX If a RADIUS server has assigned the TX bandwidth, then it will be the effective TX bandwidth. The authentication with the RADIUS sever can - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 143
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide switch throughput problems will arise and consequently affect the overall performance of the switch network. To help rectify this packet storm, the Switch of recovering the port is to manually recoup it using the System - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 144
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description From Port / from shutdown for a port. The default value is 0, which means there is no auto recovery and the port remains in shutdown forever mode. This requires manual entry of the CLI command config - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 145
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide NOTE: Traffic Control cannot be implemented on ports that are set for Link DSCP trust mode, the switch will insert the priority tag to untagged packets by using the DSCP Map settings instead of the default port priority. To view - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 146
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Apply button to accept the is ingresses to the port. The remaining processing of the packet will base on the new DSCP. By default, the DSCP is mapped to the same DSCP. To view the following window, click QoS > DSCP > - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 147
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide DSCP Map Use the drop-down menu to happens when one of the destination ports of a broadcast or multicast packet are busy. The switch will hold this packet in the buffer while the other destination port will not transmit the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 148
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 9-11 QoS Scheduling window The (WRR) algorithm to handle packets in an even distribution in priority classes of service. Click the Apply button to accept the changes made. QoS Scheduling Mechanism Changing the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 149
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 9-12 QoS Scheduling Mechanism The weighted round-robin algorithm to handle packets in an even distribution in priority classes of service. Click the Apply button to accept the changes made. NOTE: The settings you assign - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 150
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 6 ACL ACL Configuration Wizard in the creation of access profiles and ACL Rules automatically by simply inputting the address or service type and the action needed. It saves administrators a lot of time. To view this - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 151
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide IPv6 - Selecting this option will allow the user to enter a range of IPv6 addresses for this rule. Action Select Permit to specify that the packets that match the access profile are forwarded by the Switch, according to any - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 152
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Add/View Rules button to view or add ACL rules within the the window according to the requirements for the type of profile. Select Ethernet ACL to instruct the Switch to examine the layer 2 part of each packet 147 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 153
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide header. Select IPv4 ACL to instruct the Switch to examine the IPv4 address in each frame's header. Select IPv6 ACL to instruct the Switch to examine the IPv6 address in each frame's header. Select Packet Content to instruct the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 154
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide to re-write the 802.1p default priority of a packet to the manual. Tick this check box to replace the Priority value in the adjacent field. Select this option to instruct the Switch Specify that the IP precedence of the outgoing packet - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 155
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide when this access rule will be implemented on the Switch. Counter Here the user can select the counter. By checking the counter, the administrator can see how many times that the rule was hit. Ports - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 156
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-8 Add ACL Profile window (IPv4 ACL) The fields that can be configured are described below: Parameter Description Profile ID (1-6) Select ACL Type 802.1Q VLAN IPv4 DSCP IPv4 Source IP Mask IPv4 Destination IP Mask - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 157
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Select ICMP to instruct the Switch to examine the Internet form (hex 0x0-0xff. Protocol ID Mask - Specify that the rule applies to the IP protocol ID traffic. User Define - Specify the Layer 4 part mask Click the Select button - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 158
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide 1 to 256. Auto Assign - Ticking this check box will instruct the Switch to automatically assign an Access ID for the rule being created. the 802.1p default priority of a packet to the value entered in the Priority field, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 159
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide previously in this command, before forwarding it on to the specified CoS queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its original value before being forwarded by the Switch. For more - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 160
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-13 Add ACL instruct the Switch to examine the flow label field of the IPv6 header. This flow label field is used by a source to label sequences of packets such as non-default quality of service or real time service - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 161
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide ICMP Select ICMP to instruct the Switch to examine the Internet Control Message Protocol (ICMP) field in each frame's header. IPv6 Source Mask The user may specify an IP address mask for the source IPv6 address by ticking the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 162
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide to re-write the 802.1p default priority of a packet to manual. Tick this check box to replace the Priority value in the adjacent field. Select this option to instruct the Switch Specify that the IP precedence of the outgoing packet - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 163
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Time Range Name Tick the check box and enter the name of the Time Range settings that has been previously configured in the Time Range - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 164
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide . Figure 10-18 Add ACL instruct the Switch to examine the layer 2 part of each packet header. Select IPv4 ACL to instruct the Switch to examine the IPv4 address in each frame's header. Select IPv6 ACL to instruct the Switch - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 165
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide B0, B4, B8, B1 B5 B9 B116, B117 B120, protocol works and how to employ D-Link's unique Packet Content ACL to prevent ARP spoofing attack, please see Appendix E at the end of this manual. After clicking the Add/View Rules - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 166
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide to re-write the 802.1p default priority of a packet to the value manual. Replace Priority Tick this check box to replace the Priority value in the adjacent field. Replace DSCP (0-63) Select this option to instruct the Switch - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 167
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide (0-7) value. If used without an action priority, the packet is sent to the default the Switch will examine, such as the MAC source address or the IP destination address. The second part is entering the criteria the Switch will - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 168
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-23 CPU Access Profile List window The fields that can be configured are described below: Parameter Description CPU Interface Filtering Click to enable - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 169
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-24 Add CPU ACL Profile each packet header. Select IPv4 to instruct the Switch to examine the IP address in each frame's header. Select IPv6 to instruct the Switch to examine the IP address in each frame's header. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 170
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide After clicking the Show Details button, the following page will appear: Figure 10-25 CPU Access Profile Detail Information (Ethernet ACL) Click the Show All - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 171
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description Access ID (1-100) Type in CPU IPv4 ACL Profile The window shown below is the Add CPU ACL Profile window for IP (IPv4). To use specific filtering masks in this ACL profile, click the packet filtering mask - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 172
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-29 Add CPU ACL Profile (IPv4 ACL) The fields that can be configured are described below: Parameter Description Profile ID (1-5) Select ACL Type 802.1Q VLAN IPv4 DSCP Source IP Mask Destination IP Mask Protocol - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 173
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Select Type to further specify that the access profile will apply an ICMP type value, or specify Code to further specify that the access profile will apply an ICMP code value. Select IGMP to instruct the Switch to the IP Protocol - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 174
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-31 CPU Access Rule List ( Select Deny to specify that the packets that match the access profile are not forwarded by the Switch and will be filtered. VLAN Name Allows the entry of a name for a previously configured - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 175
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 176
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide packet content mask. This will change the menu according to the requirements for the type of profile. Select Ethernet to instruct the Switch to examine the layer 2 part of each packet header. Select IPv4 to instruct the Switch - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 177
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-37 Add CPU instruct the Switch to examine the flow label field of the IPv6 header. This flow label field is used by a source to label sequences of packets such as non-default quality of service or real time service - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 178
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Adding a CPU Packet Content ACL each packet header. Select IPv4 to instruct the Switch to examine the IP address in each frame's header. Select IPv6 to instruct the Switch to examine the IP address in each frame's header. Select - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 179
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide 64-79 - Enter a value in hex form to mask the packet from byte 64 to byte 79. Click the Select button to select a CPU ACL - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 180
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-42 Add CPU Access packets that match the access profile are not forwarded by the Switch and will be filtered. Offset This field will instruct the Switch to mask the packet header beginning with the offset value - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 181
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-43 CPU Access Rule Detail Information (Packet and the srTCM, the CIR is measured in bytes of IP packets. IP packet bytes are measured by taking the size of the IP header but not the link specific headers. For the 176 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 182
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide trTCM, the packet flow is IP packet that is expected in the IP flow. PIR - Peak Information Rate. This rate is measured in bytes of IP packets. IP packet bytes are measured by taking the size of the IP header but not the link - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 183
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description Profile ID Use the drop-down menu to select it and enter the Profile ID for the flow meter. Profile Name Use the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 184
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide packets with a high precedence. trTCM - Specify Profile List Egress ACL performs per-flow processing of packets when they egress the Switch. The Switch supports three Profile Types, Ethernet ACL, IPv4 ACL, and IPv6 ACL. To view - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 185
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-48 Egress Access Profile List window Click the Add Egress ACL button to add an entry to the Egress Access Profile List. Click - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 186
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-49 Add Egress ACL Profile window ( a MAC address mask for the destination MAC address. 802.1Q VLAN Selecting this option instructs the Switch to examine the 802.1Q VLAN identifier of each packet header and use this as - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 187
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide After clicking the Show Details button, the following page will appear: Figure 10-50 Egress Access Profile Detail Information window (Ethernet ACL) Click the Show - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 188
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description Access ID (1-128) Type in a unique identifier number for this access. This value can be set from 1 to 128. Auto Assign - Ticking this check box will instruct the Switch to automatically assign an Access - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 189
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Adding an IPv4 ACL Profile instructs the Switch to examine the DiffServ Code part of each packet header and use this as the, or part of the criterion for forwarding. Enter an IP address mask for the source IP address. Enter an IP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 190
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Selecting this option instructs the Switch to examine the protocol type value in each frame's header. Then the user must specify what protocol(s) to include according to the following guidelines: Select ICMP to instruct IP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 191
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Show All Profiles button This value can be set from 1 to 128. Auto Assign - Ticking this check box will instruct the Switch to automatically assign an Access ID for the rule being created. Specify the value of DSCP. The - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 192
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Priority (0-7) Tick the corresponding check box if you want to re-write the 802.1p default .1p, see the QoS section of this manual. Replace DSCP (0-63) Select this option to instruct the Switch to replace the DSCP value (in a - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 193
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide instruct the Switch to examine the class field of the IPv6 header. This class field is a part of the packet header that is similar to the Type of Service mask. Select ICMP to instruct the Switch to examine the Internet Control Message - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 194
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide 255.255.255.255. IPv6 Destination Mask The user may specify an IP address mask for the destination IPv6 address by ticking the corresponding check box and entering the IP address mask, e.g. 255.255.255.255. Click the Select - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 195
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide by the Switch and will be filtered. Tick the corresponding check box to re-write the 802.1p default priority of .1p, see the QoS section of this manual. Select this option to instruct the Switch to replace the DSCP value (in a - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 196
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide error message and the access rule will not be configured. Ticking the All Ports check box will denote all ports on the Switch. Port Group ID Specify the port group ID to apply to the access rule. Port Group Name Specify the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 197
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 10-65 Egress ACL Flow Meter Configuration window The fields that can be configured are described below: Parameter Description Profile ID (1-4) Profile Name Access - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 198
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide using this parameter and entering the DSCP value to replace. Counter - Use this parameter to enable or disable the packet counter for the specified ACL - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 199
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 7 Security 802.1X RADIUS IP-MAC-Port Binding (IMPB) MAC-based Access Control (MAC) Compound Authentication Port Security ARP Spoofing Prevention Settings BPDU Attack Protection Loopback Detection Settings Traffic - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 200
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Authentication Server The Authentication Server is Client is simply the end station that wishes to gain access to the LAN or switch services. All end stations must be running software that is compliant with the 802.1X protocol - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 201
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Authentication Process Utilizing the three detects events that indicate the attachment of an active device at the remote end of the link, or an active device becoming inactive. These events can be used to control the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 202
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Host-Based Network Access Control In order to forward PDU is enabled and 802.1X is disabled (globally or just for the port). The default state is disabled. Max Users (1-448) Specifies the maximum number of users. The limit on - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 203
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide 802.1X Port Settings Users can configure the retransmit an EAP Request packet to the Supplicant before it times out the authentication session. Its default value is 2; it can be set by management to any value in the range from - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 204
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide client. The default setting is 30 seconds. ReAuthPeriod (1-65535) A constant that defines a nonzero number of seconds between periodic reauthentication of the client. The default setting is 3600 seconds. ReAuthentication - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 205
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide is a need for non- 802.1X supported devices to gain limited access to the network Switch to be placed in a Guest VLAN when trying to access the Switch. Upon initial entry to the Switch, the client wishing services on the Switch - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 206
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide 2. A port cannot be a member of a Guest VLAN and a static VLAN simultaneously. 3. Once a client has been accepted into the target VLAN, it can no longer access - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 207
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Authenticator Statistics This window is used to display the authenticator statistics information. To view this window, click Security > 802.1X > Authenticator Statistics as shown below: - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 208
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-16 Authenticator Session Statistics window The fields that can be configured are described below: Parameter Description Time Interval Use the drop-down menu - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 209
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-17 Authenticator Diagnostics window NOTE: The user must first globally enable Authentication Mode in the 802.1X Global Settings window before initializing ports. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 210
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-19 Initialize Port(s) - MAC-based window The fields that can be configured are described below: Parameter Description From Port / To Port Select a range - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 211
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide IP address. IPv6 Address Set the RADIUS server IPv6 address. Authentication Port (165535) Set the RADIUS authentic server(s) UDP port which is used to transmit RADIUS data between the Switch and the RADIUS server. The default - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 212
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide RADIUS Accounting Settings This window is used to configure the state of the specified RADIUS accounting service. To view this window, click Security > RADIUS > RADIUS Accounting Settings as shown below: Figure 11-23 RADIUS - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 213
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-24 RAIUS Authentication window The user may also select the desired time interval to update the statistics, between 1s and 60s, where "s" stands for seconds. The default value is one second. The fields that can be - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 214
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide this server. AccessResponses The number of malformed RADIUS Access-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 215
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The user may also select the desired time interval to update the statistics, between 1s and 60s, where "s" stands for seconds. The default IP-MAC-Port Binding (IMPB) The IP network layer uses a four-byte address. The Ethernet link - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 216
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide IMPB Global Settings Users can enable or disable the Trap/Log State and DHCP Snoop state on the Switch. The Trap/Log field will enable and disable the sending of trap/log messages for IP-MAC-port binding. When enabled, the Switch - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 217
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-27 IMPB Port Settings window The fields that can be configured are described below: Parameter Description From Port / To Port Select a range of ports to set for IP-MAC-port binding. ARP Inspection When the ARP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 218
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide IMPB Entry Settings This window is used to create static IP-MAC-binding port entries and view all IMPB entries on the Switch. To view this window, click Security > IP-MAC-Port Binding (IMPB) > IMPB Entry Settings as shown below: - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 219
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the View All button to display all the existing entries. Click dynamic entries on specific ports. To view this window, click Security > IP-MAC-Port Binding (IMPB) > DHCP Snooping > DHCP Snooping Entry as shown below: 214 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 220
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide and remote RADIUS server authentication methods are supported. In MAC-based access control, MAC and otherwise will be blocked by the Switch. 3. Ports that have been enabled for Link Aggregation and Port Security cannot be enabled - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 221
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-32 MAC-based Access RADIUS server, which is to be used for packets being sent requesting authentication. The default password is "default". Use the drop-down menu to enable or disable the use of RADIUS Authorization. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 222
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Member Ports Enter the list of select the Infinite option. Block Time (0-300) Enter a value between 0 and 300 seconds. The default is 300. Max User (1-1000) Enter the maximum user used for this configuration. When No Limit - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 223
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide all the information linked to the port default button to go back to the default settings of all elements. Compound Authentication Compound Authentication settings allows for multiple authentication to be supported on the Switch - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 224
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Compound Authentication Settings Users can configure Authorization Network State Settings and compound authentication methods for a port or ports on the Switch the original VLAN. Block (default setting). The client is always - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 225
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide on a port at the same time. In Any (MAC, 802.1X, the changes made for each individual section. NOTE: Per VLAN authentication is only supported by Captive Portal. If Authentication Method is not None, the port will work as - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 226
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Port Security Port Security Settings A given State Lock Address Mode Click to enable or disable Port Security traps and logs on the Switch. Enter the system maximum address. Tick the No Limit check box to have unlimited system - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 227
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide DeleteOnReset - The locked addresses will not age out until the Switch has been reset or rebooted. Max Learning Address (0-3072) Specify the maximum value of port security entries that can be learned on this port. Click - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 228
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Max Learning Address Specify the maximum number for the protected gateway. When an entry is created, those ARP packets whose sender IP matches the gateway IP of an entry, but either its sender MAC field or source MAC field does - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 229
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-43 ARP Spoofing Prevention Settings window The fields that can be configured are described below: Parameter Description Gateway IP Address Enter the gateway IP address to help prevent ARP Spoofing. Gateway MAC - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 230
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-44 BPDU Attack Attack Cleared or Both. Recover Time (601000000) Specify the BPDU protection Auto-Recovery timer. The default value of the recovery timer is 60. Tick the Infinite check box for not recovering the port - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 231
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Loopback Detection port will restart (change seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop-detect Recover Time. The default is 60 seconds. From Port / To Port Use the drop-down menus to select a range of - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 232
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide NetBIOS Enhanced User Interface, was created as a data-link-layer frame structure for NetBIOS. A simple mechanism to carry in RFC 1001 and RFC 1002, NetBIOS over TCP/IP (NBT). If the network administrator wants to block the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 233
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide the network and both provide DHCP services to different distinct groups of clients . The Source IP address is the same as the DHCP server's IP address (UDP Server Screening Port Settings The Switch supports DHCP Server Screening, a - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 234
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-48 DHCP Server Screening . State Choose Enabled to enable the DHCP server screening or Disabled to disable it. The default is Disabled. Click the Apply button to accept the changes made for each individual section. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 235
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description Server IP Address The IP address of access to the Switch. There are currently three versions of the TACACS security protocol, each a separate entity. The Switch's software supports the following versions - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 236
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide listed for authentication. If the first technique goes through its Authentication Server Hosts and no authentication is returned, the Switch configured by the administrator that will support the "enable" function. This function - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 237
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Authentication Policy Settings Users can enable an administrator-defined authentication policy for users trying to access the Switch from the Switch. The user may set the number of attempts from 1 to 255. The default setting is - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 238
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide (Command Line Interface) application, the Telnet admin-level users utilizing a previously configured method list. The user may use the default Method List or other Method List configured by the user. See the Enable Method - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 239
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-55 Authentication Server Group Settings - Edit Server Group window To add an Authentication Server Host to the list, enter its name in the Group Name field, IP address in the IP . The maximum supported number of server - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 240
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description IP Address The IP address of define the virtual port number of the authentication protocol on a server host. The default port number is 49 for TACACS/XTACACS/TACACS+ servers and 1813 for RADIUS servers - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 241
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The Switch contains one Method List that is set eight Enable Method Lists can be implemented on the Switch, one of which is a default Enable Method List. This default Enable Method List cannot be deleted but can be configured - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 242
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-58 Enable method Lists Settings parameter will require the user to be authenticated using the local enable password database on the Switch. The local enable password must be set by the user in the next section entitled - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 243
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The fields that can be configured are downloaded to the Switch by utilizing a TFTP server. The Switch supports SSLv3. Other versions of SSL may not be compatible with this Switch and may cause problems upon authentication - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 244
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Users can download a certificate file for the SSL function on the Switch Switch only supports certificate files with .der file extensions. Currently, the Switch . This field is Enabled by default. This cipher suite combines the RSA - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 245
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide suite. This field is Enabled by default. Click the Apply of Secure Shell, which is a program allowing secure remote login and secure network services over an insecure network. It allows a secure login to remote host computers, a - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 246
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-61 SSH Settings window The fields that can be configured are described below: Parameter Description SSH Server State Use the radio buttons to enable or disable SSH on the Switch. The default is Disabled. Max. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 247
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The fields that can be configured for the HMAC (Hash for Message Authentication Code) mechanism utilizing the Secure Hash algorithm. The default is enabled. Click the Apply button to accept the changes made. The fields that can - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 248
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description HMAC-RSA Use the check box to enable or disable the HMAC (Hash for Message Authentication Code) mechanism utilizing the RSA encryption algorithm. The default Host IP Enter the corresponding IP address - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 249
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Trusted Host Settings Up to thirty trusted host secure IP addresses or ranges may be configured and used for remote Switch management. It should be noted that if one or more trusted hosts are enabled, the Switch select services - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 250
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide mode, when the Switch either (a) receives too many packets to process or (b) exerts too much memory, it will enter the Exhausted mode. When in this mode, the Switch will drop all ARP and IP broadcast packets and packets from un- - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 251
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Fuzzy - If selected, this function will instruct the Switch to minimize the IP and ARP traffic flow to the CPU by the Switch, and will stop receiving all unnecessary broadcast IP packets, until the storm has subsided. The default - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 252
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Disabled, IP Address Not Configured, No IP Routing Interface default port (443) is used. Peer Switch Statistics Reporting Interval (15-3600) When clustering is supported on the switch, enter an interval that the peer switches - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 253
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-68 CP configuration - CP Summary window to navigate to a specific page when multiple pages exist. Click the link under Configuration in the table, or the tab to configure the detail information about CP configuration. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 254
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-69 CP Configuration - before automatically being logged out. The value 0 indicates that the timeout is not enforced. The default value is 0. Enter the waiting time in seconds before terminating a session. A user is - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 255
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Language Subtag Registry. If the language is supported by the Switch, this field is filled in automatically when to wipe all the configurations and set back to the default settings. Click the language tab to customize the CP web - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 256
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Clear button to wipe all the configurations and set back to the default settings. Select Authentication Page from the drop-down menu on the the text to instruct users to authenticate. Enter the text to display next to the user - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 257
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Use Policy text box. The acceptance use policy instructs users about the conditions under which they are allowed to wipe all the configurations and set back to the default settings. Click the Preview button to view the result - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 258
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Clear button to wipe all the configurations and set back to the default as the page title. Instruction Text Enter the detailed information to confirm that the user has been authenticated and instructs the user how to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 259
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Title Enter the text to use as the page title. Instructional Text Enter the message to confirm that the user has to wipe all the configurations and set back to the default settings. Click the Preview button to view the result of - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 260
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-75 Local User - Summary window Click the Add button to create a new user to the local database. Tick the corresponding check box, and - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 261
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide User Group Assign the user to at Timeout (secs) Enter the time in seconds that allows the user to remain idle before the Switch automatically logs the user out. Max Up Rate (bytes/sec) Enter the maximum transmitting speed, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 262
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide (bytes/sec) portal. Max Down Rate (bytes/sec) Enter the maximum receiving speed, in bytes per second, when using the captive portal. Max Receive (bytes) - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 263
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-79 CP Global Status window The fields that can be displayed are described below: Parameter Description CP Global Operational Status CP Global Disable Reason CP IP Address Supported Local Users Supported Captive - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 264
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-80 CP Activation and Activity Status window Use the drop-down menu to select a CP to see its activation and activity status. Click - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 265
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-82 Interface Capability Status window The fields that can be displayed are described below: Parameter Description Bytes Received Counter Display whether the interface supports displaying the number of bytes - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 266
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-83 Client Summary the authenticated client is authenticated by a peer switch. In other words, the cluster controller was not the authenticator. IP Address Display the IP address of the wired client (if applicable). - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 267
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-84 Client Connection Status window The fields that can be displayed are described below: Parameter Description Client IP Address Display the IP address of the wired client (if applicable). User Name Display the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 268
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-85 Client Statistics window Use the drop-down menu to select the MAC address of the associated client to view the statistical information. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 269
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-87 CP-Client Status window Use the drop-down menu to select a CP to see the information of the clients connected to the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 270
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide 265 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 271
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 8 Network Application DHCP SNTP Option 82 State Use the drop-down menu to enable or disable the DHCP Relay service on the Switch. The default is Disabled. Enter an entry between 1 and 16 to define the maximum number of - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 272
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide it can implement policies like restricting the number of IP addresses that can be assigned to a single Switches policy for handling packets when the DHCP Relay Agent Information Option 82 Check is set to Disabled. The default - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 273
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide NOTE: If the Switch receives a packet that contains the option 82 field from a DHCP client and the information-checking feature is enabled, the Switch drops the packet because it is invalid. However, in some instances, users may - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 274
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide this window. Properly configured settings will be displayed in the DHCP Relay Interface Table at the bottom of the window, once the user clicks the Apply button. The user may add up to four server IPs per IP interface on the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 275
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide This option decides whether the DHCP string in the packet only need partial match with the specified string. IP Address Enter the DHCP Relay Option 60 IP address. String Enter the DHCP Relay Option 60 String value. Click - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 276
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 12-7 DHCP Relay Option 61 Settings window The fields that can be configured are described below: Parameter Description DHCP Relay Option 61 Default Here the user can select the DHCP Relay Option 61 default action. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 277
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide to access national time and frequency dissemination services, organize the SNTP subnet of servers and The IP address of the primary server from which the SNTP information will be taken. SNTP Second Server The IP address - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 278
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 12-10 Time Zone Settings window The fields that can be configured are described below: Parameter Description Daylight Saving Time State Daylight Saving Time - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 279
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide enough, the user could download more configuration files or firmware files and use commands to display Flash file information, link to navigate the C: drive After clicking the C: link button, the following page will appear: 274 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 280
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 12-12 Flash File System Setting - Search for Drive window Click the Previous button to return to the previous window. Click the Create Directory to create a new directory within the file system of the switch. Click the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 281
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 9 CFM Ethernet OAM Cable Diagnostics OAM . MIP This is the control creations of MIPs. None - Don't create MIPs. This is the default value. Auto - MIPs can always be created on any ports in this MD, if that port - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 282
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Edit button to re-configure the specific entry. Click the Delete button to remove the specific entry. NOTE: The MD Name value should - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 283
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Auto - MIPs can always be created on any ports the MEP ID is 1-8191. Add - Add MEP ID(s). Delete - Delete MEP ID(s). By default, there is no MEP ID in a newly created maintenance association. Click the Apply button to accept - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 284
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The fields that can be configured are NOTE: The MEP Name value should be less than 32 characters. After clicking the View Detail link, the following page will appear: Figure 13-6 CFM MEP Information Window Click the Edit button - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 285
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 13-7 CFM MEP Information - Edit Window the fault can be realarmed. The unit is in centiseconds, the range is 250-1000. The default value is 1000 Click the Apply button to accept the changes made. Click the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 286
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 13-8 CFM Extension AIS Window The set to 1 minute. Level The client level ID to which the MEP sends AIS PDU. The default client MD level is MD level at which the most immediate client layer MIPs and MEPs exist. Options - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 287
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide CFM Port Settings This window is used to enable or disable the CFM function on a per-port basis. To view this window, click OAM > CFM > - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 288
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide sent. The default value is 4. LBM Payload Length (0-1500) The payload length of LBM to be sent. The default is 0. LBM used to issue a CFM link track message, display or delete the link trace responses. To view this window, click - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 289
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 13-13 CFM Linktrace Settings Window MAC Address Here the user can enter the destination MAC address. TTL (2-255) Link-trace message TTL value. The default value is 64. PDU Priority The 802.1p priority to be set in the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 290
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 13-14 CFM Packet Counter Window The fields that can be configured are described below: Parameter Description Port List Enter a list of ports to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 291
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide MA Index Select and enter the Maintenance Association index used. Click the Find button to locate a specific entry based on the information entered. CFM MP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 292
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 13-17 Ethernet OAM Settings window The fields that can be configured are described below: Parameter Description From Port / To Port Select a range of - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 293
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 13-18 Ethernet OAM Configuration Settings window The fields that can be configured are described below: Parameter Description From Port / To Port Select a range of ports you wish to configure. Link Event Use the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 294
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 13-19 Ethernet OAM Event Log window The fields that can be configured are described below: Parameter Description Port Use the drop-down menu - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 295
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 13-20 Ethernet OAM Cable Diagnostics The cable diagnostics feature is designed primarily for administrators or customer service representatives to verify and test copper cables; it can rapidly determine the quality - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 296
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide To view the cable diagnostics for a particular . Cable length detection is only supported on GE ports. Ports must be linked up and running at 1000M speed. Cross-talk errors detection is not supported on FE ports. NOTE: The - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 297
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 10 Utilization Statistics Mirror sFlow "s" stands for seconds. The default value is one second. Record Number Select number of times the Switch will be polled between 20 and 200. The default value is 200. Show/Hide - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 298
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 14-2 DRAM & Flash Utilization window where "s" stands for seconds. The default value is one second. Record Number Select number of times the Switch will be polled between 20 and 200. The default value is 200. Show/Hide - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 299
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Port Statistics Packets The Web manager allows various packet statistics to be Figure 14-4 Received (RX) window (for Bytes and Packets) Click the View Table link to display the information in a table rather than a line graph. 294 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 300
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide default value is one second. Record Number Select number of times the Switch will be polled between 20 and 200. The default Table link to display the information in a table rather than a line graph. Click the View Graphic link to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 301
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 14-6 UMB_cast (RX) window (for Unicast, Multicast, and Broadcast Packets) Click the View Table link The default value is one second. Select number of times the Switch will be polled between 20 and 200. The default value - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 302
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Multicast Counts the total number of counters on this window. Click the View Table link to display the information in a table rather than a line graph. Click the View Graphic link to display the information in a line graph - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 303
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide default value is one second. Record Number Select number of times the Switch will be polled between 20 and 200. The default Table link to display the information in a table rather than a line graph. Click the View Graphic link to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 304
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 14-10 Received (RX) window (for errors) Click the View Table link to display for seconds. The default value is one second. Select number of times the Switch will be polled between 20 and 200. The default value is 200. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 305
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide UnderSize The number of packets detected counters on this window. Click the View Table link to display the information in a table rather than a line graph. Click the View Graphic link to display the information in a line graph - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 306
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide default value is one second. Record Number Select number of times the Switch will be polled between 20 and 200. The default Table link to display the information in a table rather than a line graph. Click the View Graphic link to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 307
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 14-14 Packet Size window Click the View Table link to display the information in a table "s" stands for seconds. The default value is one second. Select number of times the Switch will be polled between 20 and 200. The - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 308
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide View Graphic link to display the information in a line graph rather than a table. Mirror The Switch allows you port. This is useful for network monitoring and troubleshooting purposes. Port Mirror Settings To view this window, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 309
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide RX Click the radio buttons to a 100 Mbps port onto a 10 Mbps port, this can cause throughput problems. The port you are copying frames from should always support an equal or lower speed than the port to which you are sending - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 310
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 14-18 RSPAN Settings - Modify the output port list for the RSPAN VLAN packets. If the redirect port is a Link Aggregation port, the Link Aggregation behavior will apply to the RSPAN packets. Tick Add or Delete to add or - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 311
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide sFlow Analyzer Server Settings The Switch can support 4 different analyzer server will be deleted. If not specified, its default value is 400. Collector Address The IP address of the analyzer server. If not specified or set - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 312
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide NOTE: If the user wants the change the 5120 packets. If set to 0, the sampler is disabled. If the rate is not specified, its default value is 0. MAX Header Size (18256) The maximum number of leading bytes in the packet which - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 313
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide ) Repeat Pinging for Size (EI Mode Only) Timeout Enter an IP address to be pinged. Enter an IPv6 address to be pinged. value between 1 and 6000. The default is 100. Select a timeout period between 1 and 99 seconds for this Ping - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 314
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide destination. If the packet fails to find the IP address in this . Trace Route The trace route page allows the user to trace a route between the switch and a given host on the network. To view this window, click Monitoring > Trace - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 315
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Port (30000-64900) The port number. The to 65535 seconds can be specified. The default is 5 seconds. Probe (1-9) The number of probing. The range is from 1 to 9. If unspecified, the default value is 1. Click the Start button - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 316
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 11 Save and Tools 311 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 317
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Section 3 WLAN This section describes all the available configurations in the WLAN tab. Chapter 1 Captive Portal (CP) Security Captive Portal (CP) Captive Portal (CP) is - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 318
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Peer Switch Statistics Reporting Interval (15-3600) When clustering is supported on the switch, enter an interval that the peer switches exist. Click the link under Configuration in the table, or the tab - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 319
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide After clicking the link or the tab, the following being logged out. The value 0 indicates that the timeout is not enforced. The default value is 0. Enter the waiting time in seconds before terminating a session. A user - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 320
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Language Subtag Registry. If the language is supported by the Switch, this field is filled in automatically when to wipe all the configurations and set back to the default settings. Click the language tab to customize the CP web - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 321
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide button. You . Click the Clear button to wipe all the configurations and set back to the default settings. Select Authentication Page from the drop-down menu on the top of the Enter the text to instruct users to authenticate. 316 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 322
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Use Policy text box. The acceptance use policy instructs users about the conditions under which they are allowed to wipe all the configurations and set back to the default settings. Click the Preview button to view the result - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 323
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Text Enter the optional text to further identify the network to be access by the CP user. Click the Apply button to accept the changes made. Click the Clear button to wipe all the configurations and set back to the default - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 324
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Title Enter the text to use as the page title. Instructional Text Enter the message to confirm that the user has to wipe all the configurations and set back to the default settings. Click the Preview button to view the result of - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 325
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 1-9 Local User - Summary window Click the Add button to create a new user to the local database. Tick the corresponding check box, and click the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 326
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide User Group Assign the user to at Timeout (secs) Enter the time in seconds that allows the user to remain idle before the Switch automatically logs the user out. Max Up Rate (bytes/sec) Enter the maximum transmitting speed, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 327
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide (bytes/sec) portal. Max Down Rate (bytes/sec) Enter the maximum receiving speed, in bytes per second, when using the captive portal. Max Receive (bytes) - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 328
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 1-13 CP Global Status window The fields that can be displayed are described below: Parameter Description CP Global Operational Status CP Global Disable Reason CP IP Address Supported Local Users Supported Captive - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 329
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 1-14 CP Activation and Activity Status window Use the drop-down menu to select a CP to see its activation and activity status. Click Block - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 330
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 1-16 Interface Capability Status window The fields that can be displayed are described below: Parameter Description Bytes Received Counter Display whether the interface supports displaying the number of bytes - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 331
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 1-17 Client Summary authenticated client is authenticated by a peer switch. In other words, the cluster controller was not the authenticator. IP Address Display the IP address of the wireless client (if applicable - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 332
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 1-18 Client Connection Status window The fields that can be displayed are described below: Parameter Description Client IP Address Display the IP address of the wireless client (if applicable). User Name Display - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 333
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 1-19 Client Statistics window Use the drop-down menu to select the MAC address of the associated client to view the statistical information. After - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 334
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 1-21 CP-Client Status window Use the drop-down menu to select a CP to see the information of the clients connected to the CP. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 335
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide 330 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 336
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 2 Global Peer Switch Access Point Client QoS Monitoring Global The Unified Switch periodically collects information from the APs it manages and from associated peer switches. This window is used to show status and - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 337
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Cluster Controller IP Address Total Access Points Managed Access Points Standalone Access Points Rogue Access Points Discovered Access Points Connection Failed Access Points Authentication Failed Access Points Unknown - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 338
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Total Pre-authentication Current number of pre-authentication history entries in use by the system. History Entries Maximum Roam History Maximum number of entries that - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 339
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-2 Switch Status window Use the drop-down menu to select a Switch is the same, the switch with lowest IP address becomes the Cluster Controller. A priority of 0 means that the switch cannot become the Cluster Controller - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 340
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Transmitted WLAN Packets Transmitted Total packets transmitted across all APs managed by the switch. WLAN Bytes Received Total bytes received across all APs managed by the switch. WLAN Packets Received Total packets - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 341
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Total Number of Discovered-Filed Entries Display the amount of devices that have an IP address configured in the IP Discovery list that the switch has attempted to contact and failed to authenticate or validate. Total Entries - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 342
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide • Global - Receive the basic and advanced global settings. • Discovery - Receive the L2 and L3 discovery information, including the VLAN and IP and the supported IEEE 802.11 modes. Display whether the hardware supports one radio - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 343
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide After clicking the Hardware Type hyperlink or the Radio Count Radio Type Description VAP Count 802.11a Support 802.11bg Support 802.11n Support Display the number of radios supported on the hardware platform, which is either 1 or - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 344
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-7 AP Hardware Capability - Image Table window and clients. The switch maintains a database with this data so you can view information about a peer, such as its IP address and software version. One switch in a cluster - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 345
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-9 Peer Switch - Status window The fields that can be displayed are described below: Parameter Description Total Entries IP Address Vendor ID Software Version Protocol Version Discovery Reason Managed AP Count Age - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 346
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-10 Peer Switch - Configuration window The fields that can be displayed are described below: Parameter Description Total Entries Peer IP Address Configuration Switch IP Address Configuration Timestamp Total number - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 347
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-11 Peer Switch - Managed AP window Use the drop-down menu to select the IP address of a peer switch. The fields that can be displayed are described below: Parameter Description Total Entries Total number of - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 348
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-12 All AP Status L3 network boundary, then 'Unknown' is displayed. IP Address The network address of the access point. Software Version Display the version of D-Link Access Point software that the AP is running. Age - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 349
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Managed AP Status This window is used to display a variety of information about each AP that the Switch MAC Address Location IP Address Profile Software Version Status The Ethernet address of the Unified Switch- managed AP. If - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 350
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Configuration Status This status indicates if The fields that can be displayed are described below: Parameter Description IP Address IP subnet Mask Status The IP address of the managed AP. The subnet mask of the managed - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 351
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Software Version Code Download Status Configuration Status Vendor ID Part Number Hardware Type Managing Switch Switch MAC Address Switch IP Address Profile Discovery Reason is enabled), but it is not configured. • Managed - The - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 352
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide • IP Poll Received - The AP was discovered via an IP poll from the Unified Switch, its IP address is configured in the IP polling list. • Peer Redirect - The AP was discovered through a peer switch redirect, the AP tried to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 353
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Channel The current operating channel for the Supported Channels Channel Channel Bandwidth Fixed Channel Indicator Manual Channel Adjustment Status WLAN Utilization The list of eligible channels the AP reported to the switch - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 354
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Authenticated Clients Transmit Power Fixed Power Indicator Manual Power Adjustment Status Total Neighbors Supported Channel Radar Detection Required Radar Detected Time Since Radar Last Detected statistics. Total count of - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 355
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The fields that can be displayed are described below: Parameter Description Neighbor AP MAC The Ethernet MAC address of the neighbor AP network, this could be a physical radio interface or VAP MAC address. For D-Link APs - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 356
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Neighbor Client MAC The Ethernet address of radio. • Associated to Peer AP - The client is associated to an AP managed by a peer switch. • Ad Hoc Rogue - The client was detected as part of an Ad Hoc network. Age Indicate - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 357
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-20 Managed AP Status - Distributed Tunneling window Use the drop down menu to select AP's MAC address to view the distributed tunneling information. The - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 358
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-21 Managed AP Statistics - WLAN Summary window The fields that can be displayed are described below: Parameter Description MAC Address The Ethernet address of the Unified Switch-managed AP. Packets Received Total - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 359
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The fields that can be displayed are described below: Parameter Description MAC Address The Ethernet address of the Unified Switch-managed AP. Packets Received Total packets received by the AP on the wired network. Bytes - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 360
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Ethernet Packets Received Ethernet Bytes a unicast packet before sending to the wireless link. Number of ARP requests that AP was able to drop instead of sending on the wireless link. The number of ARP requests sent as broadcasts - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 361
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide WLAN Packets Received Dropped WLAN Bytes Received Dropped WLAN Packets Transmit Dropped WLAN Bytes Transmit Dropped Fragments Received Fragments Transmitted Multicast Frames Received Multicast Frames - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 362
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-25 Managed AP Statistics - VAP window Use on each VAP on specified radio for a particular access point managed by the Switch. The fields that can be displayed are described below: Parameter Description WLAN Packets - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 363
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-26 Managed AP Statistics - Distributed Tunneling window Use the drop down menu to select AP's MAC address to view information about the number of - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 364
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 365
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-30 AP RF Scan Status - Detail AP. This could be a physical radio interface or VAP MAC. For D-Link APs this is always a VAP MAC address. Service Set ID of the network, which is broadcast in the detected beacon frame. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 366
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Physical Mode Security Mode 802.11n Mode Beacon Interval Highest Supported detected AP. This could be a physical radio interface or VAP MAC. For D-Link APs this is always a VAP MAC address. Display whether the AP that detected - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 367
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide After clicking the WIDS AP Rogue radio interface or VAP MAC. For D-Link APs this is always a VAP MAC address. Display the managed status of the AP, whether this is a valid AP known to the Switch or a Rogue on the network. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 368
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Test Config Test Result Time Since APs are classified as rogues before enabling the attack feature. This feature is disabled by default. The wireless system can conduct the de-authentication attack against 16 APs at the same - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 369
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-34 Associated Clients Status - by an asterisk (*), the client is associated with an AP managed by a peer switch. Detected IP Address Display the IPv4 address of the client. NetBIOS Name The NetBIOS name of the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 370
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-35 Associated Clients Status - Detail window The fields that can be displayed are described below: Parameter Description SSID BSSID AP MAC Address Status Channel - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 371
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide is associated. Location The descriptive STBC Capable Display the Space Time Block Code (STBC) mode of the client. Detected IP Address Display the IPv4 address of the client. Click the drop-down menu to select a - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 372
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide kbps. A value of 0 means no bandwidth limiting MAC Address Location Radio Discovery Reason The base Ethernet address of the Unified Switch managed AP. The configured descriptive location for the managed AP. The radio interface - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 373
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide switch. • Ad Hoc Rogue - The client was detected Associated AP MAC Address Display whether this client is associated with a network that supports L2 distributed tunneling. Display whether the client is on the Home AP or has - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 374
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-39 Associated Clients SSID Status window The fields that can be displayed are described below: Parameter Description SSID The network on which the client - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 375
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide BSSID The Ethernet MAC address for 2-41 Associated Clients Switch Status window The fields that can be displayed are described below: Parameter Description Switch IP Address The IP address of the switch that manages the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 376
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-42 Associated Clients Statistics - Summary window The fields that can be displayed are described below: Parameter Description MAC Address The Ethernet address of the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 377
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide If the client roams from one AP to another AP but remains connected to the same network, the session continues and the session statistics continue - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 378
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Bytes Transmit Dropped Fragments Received Fragments transmits while it is connected to the same WLAN network shared by APs that the switch manages. Each client is identified by its MAC address Figure 2-45 Associated Clients - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 379
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Duplicates Received Total duplicate packets received from the client station. Detected Clients This window is used to display the information about clients that have authenticated - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 380
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide After clicking the MAC address hyperlink, the following page will appear: Figure 2-47 Detected Client Summary -Detected Client Status window The fields that can be - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 381
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide authenticated. The possible range is from -128 Authe msgs Display the largest number of de-authentication messages that the switch detected during a de-authentication collection interval. Authentication Failures Display the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 382
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-48 Detected Client Summary -WIDS Client Rogue Classification window The fields that can be displayed are described below: Parameter Description MAC Address The Ethernet - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 383
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-49 Detected Client Summary -Pre-Auth History window The fields that can be displayed are described below: Parameter Description MAC Address AP MAC Address - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 384
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-50 Detected Client Summary -Triangulation window The fields that can be displayed are described below: Parameter Description MAC Address MAC address of the client. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 385
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-51 Detected Client Summary -Roam History window The fields that can be displayed are described below: Parameter Description MAC Address AP MAC Address Radio - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 386
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-52 Detected Client Pre-Authentication History Summary window The fields that can be displayed are described below: Parameter Description MAC Address AP MAC Address - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 387
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Allow MAC button to add the MAC address, which default action is allow, to the Known Clients window and exist. QoS Access Control Lists IP Access Control Lists This window is used to display the IP access control lists (ACL). - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 388
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-55 IP Access Control Lists window Use the Type Select drop-down menu to display various types of IP ACL. Click the Rules ID hyperlink to see the detail information about the rule. Enter a page number and click the Go - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 389
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-57 IP Access Control Lists - Rule ID window (Extended IP ACL) The fields that can be displayed are described below: Parameter Description IP ACL Name The ID of the IP ACL. Rule ID The number identifier for each - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 390
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description IP ACL Name The name of the IP ACL. Rule ID The number identifier for each rule that is defined for the IP ACL. Action The action associated with each rule. Available values are Permit and Deny. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 391
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description IPv6 ACL Name IPv6 ACL The destination port for this rule. Flow Label The value of IPv6 flow label. IP DSCP Service The DSCP keyword value. Click the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 392
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description MAC ACL Name MAC . Differentiated Services Class Summary This window is use to display the differentiated service class. To view this window, click Monitoring > QoS > Differentiated Services > Class - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 393
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-64 Policy Summary window The fields Ethertype, Source MAC Address, VLAN, Class of Service, Any, IP DSCP, IP Precedence, IP TOS, Protocol Keyword, Reference Class, Source IP Address, and Source Layer 4 Port. Values The - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 394
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-66 Policy Attribute Summary window The fields that can be displayed are described below: Parameter Description Policy Name The name of this policy. Policy - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 395
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 3 Administration Basic Setup AP Management switch to automatically assign itself an IP address. Switch Static IP Address If the Auto IP Assign Mode is disabled, a static IP address of the Switch must be manually - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 396
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-2 Basic Setup Discovery window The fields that can be configured are described below: Parameter Description L3/IP Discovery Tick the check box to enable IP-based discovery of access points and peer wireless - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 397
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-3 Basic Setup Profile window The connected to the wired network. The tracer packets help the switch identify unauthorized APs that do not belong to the D-Link Unified Access System but are connected to the wired network - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 398
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description Wireless Default Radio Settings State Mode box to allow the radio to operate in sentry mode. Display the channels supported for the radio mode. The available channels vary based on the selected Country - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 399
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide channel assignment process. Available MSC Indices Tick the check boxes to add MCS Index when operating in 802.11n mode. Rate Sets (Mbps) Display the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 400
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-6 Basic Setup SSID - Edit window this feature. The distributed L2 tunneling mode supports L3 roaming for wireless clients without forwarding any data traffic to the Unified Switch. Use the drop-down menu to enable - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 401
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide L3 Tunnel L3 Tunnel Status L3 Tunnel Subnet L3 Tunnel Mask RADIUS Use Network Configuration RAIDUS Accounting Security Option 2. If the network has peer switches obtains a new IP address. 3. If the switch managing the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 402
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide WEP Wired Equivalent Privacy (WEP) is a data encryption protocol for 802.11 wireless networks. If this security mechanism is selected, all wireless clients and access - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 403
Client QoS DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide WPA/WPA2 WPA and WPA2 are management. • WPA Versions - Tick the check boxes to select the types of client stations to support. Available options are WPA and WPA2. • WPA Ciphers - Tick the check boxes to select the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 404
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide associate with the AP using the SSID the changes made. Click the Clear button to discard the changes made and return to the default settings. After clicking the Valid AP tab, the following page will appear: Figure 3-7 Basic - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 405
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Enter a page number and click the Go Managed Select this to have the AP being part of the D-Link Unified Switch, and it can be managed by the Unified Switch. When Managed is selected, the following options appear at the bottom - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 406
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Standalone Select this to have the AP acting as an individual access point in the network. When Standalone is selected, the following options appear at - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 407
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide OUI Description Enter the organization name AP Management AP Reboot This window is used to reboot one or all APs from the Unified Switch. To view this window, click Administration > AP Management > AP Reboot as shown below: - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 408
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The fields that can be configured are described below: . The default is Manual. • Manual - The proposed power adjustments are run manually from the Manual Power Adjustments page. • Interval - The switch periodically calculates - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 409
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-12 RF Management Channel Plan History window algorithm last ran. NOTE: To set the system time on the Switch, you must use SNTP, which is disabled by default. From the Web interface, you configure the SNTP settings in - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 410
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide • The channel is not valid for the radio mode. • The AP has been rebooted since the channel plan was computed and acquires a static channel that has been set statically via local database. • The channel has been set manually - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 411
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the radio buttons to select the radio frequency the plan. • None - The power adjustment algorithm has not been manually run since the last switch reboot. • Algorithm In Progress - The power adjustment algorithm is running. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 412
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Software Download This window is used to upgrade software on the APs that the Switch manages. The Cluster Controller can update code on APs managed by peer wireless switches. To view this window, click Administration > AP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 413
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-16 AP Image Management window The fields that can be configured are described below: Parameter Description TFTP Server IP Enter the IP address of the TFTP server. Source File Enter the file name. Image Type Use - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 414
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-18 Advanced Settings - Debug window The fields that can be configured are described below: Parameter Description Password Enter the admin password for the AP. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 415
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-20 AP Provisioning window Tick the specific can be configured are described below: Parameter Description MAC Address New Primary IP Use the drop down menu to select the MAC address of the AP. Tick the check box - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 416
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Address provisioned. New Backup IP Address Tick the check box and enter IP address of the backup switch that the AP to be provisioned. Profile ID Use the drop-down menu to select the profile ID to be used when provisioning. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 417
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide addresses, specified in the Known Client NOTE: If any of the following conditions are true, there is no need to increase the tunnel IP MTU size: • The wireless network does not use L3 tunneling. • The tunneling mode is used - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 418
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-23 Global SNMP Traps window The fields that can be configured are described below: Parameter Description AP Failure Traps Select Enable to allow the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 419
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-24 Global Distributed Tunneling tunnel to that client Timeout is terminated, and the client is forced to change its IP address. Distributed Tunnel Timeout Enter the time in seconds before the tunnel to the roamed - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 420
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The fields that can be configured are described : Parameter Description SSID Hide SSID Deny Broadcast VLAN MAC Authentication Redirect Enter Service Set Identifier (SSID) of the network, which is an alphanumeric key that - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 421
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide mode supports L3 roaming for wireless clients without forwarding any data traffic to the Unified Switch. the client re-associates it obtains a new IP address. 3. If the switch managing the association AP fails, then the scenario - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 422
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide WEP Wired Equivalent Privacy (WEP) is a data encryption protocol for 802.11 wireless networks. If this security mechanism is selected, all wireless clients and access - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 423
Client QoS DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide WPA/WPA2 WPA and WPA2 are management. • WPA Versions - Tick the check boxes to select the types of client stations to support. Available options are WPA and WPA2. • WPA Ciphers - Tick the check boxes to select the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 424
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide associate with the AP using the the changes made. Click the Clear button to discard the changes made and return to the default settings. AP Profiles This window is used to create, configure, delete AP profiles. AP profiles - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 425
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Tick the check box of a specific Link Unified Access System but are connected to the wired network. Click the Apply button to accept the changes made. Click the Clear button to discard the changes made and return to the default - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 426
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-29 AP Profile Configuration - 11a, IEEE 802.11a/n and 5GHzIEEE 802.11n. When 2-802.11b/g/n is selected in Wireless Default Radio Settings, available options are IEEE 802.11b/g, IEEE 802.11b/g/n and 2.4GHzIEEE 802.11n - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 427
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Beacon Interval (msecs) Load Balancing Local Utilization (%) Maximum Clients Automatic Channel Automatic Power Default should not acknowledge frames with QosNoAck as the service class value. Select Enable to enable Unscheduled - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 428
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide equal to the RTS Threshold. Long Retries Display the maximum number of transmission attempts on frame sizes greater than the RTS Threshold. Transmit Lifetime (msecs) - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 429
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-30 AP Profile Configuration - VAP window The fields that can be configured are described below: Parameter Description Access Point Profile VAP Configuration Click to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 430
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter SSID Hide SSID Deny Broadcast VLAN MAC Authentication Redirect Redirect URL Wireless ARP Suppression Mode L2 Distributed Tunneling Mode L3 Tunnel L3 Tunnel Status L3 Tunnel Subnet Description Enter Service Set - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 431
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide L3 Tunnel Mask RADIUS Use Network Configuration RAIDUS Accounting Security Option Enter the subnet mask for the network IP address on the L3 Tunnel subnet. This parameter is used to control whether the VAP uses the network or - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 432
Client QoS DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide WPA/WPA2 WPA and WPA2 are management. • WPA Versions - Tick the check boxes to select the types of client stations to support. Available options are WPA and WPA2. • WPA Ciphers - Tick the check boxes to select the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 433
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide associate with the AP using the SSID the changes made. Click the Clear button to discard the changes made and return to the default settings. After clicking the QoS tab under the Profile Name tab, the following page will appear - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 434
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide cwMax (msecs) Enter the upper limit, in milliseconds, for the total number of peer switches that have failed to complete a configuration download. Peer IP Address Lists the IP address of each switch in the cluster and - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 435
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide After clicking the Configuration Enable/Disable tab, the following page will appear: Figure 3-34 Peer Switch Configuration Enable/Disable window The fields that can be configured are described below: Parameter Description - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 436
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-35 Peer Switch Mutual Authentication window The fields that can be configured are described below: Parameter Description Switch Provisioning Select Enabled to enable switch The D-Link Unified Switch Wireless - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 437
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 3-36 WIDS Security AP Configuration window The fields from a managed AP If the source MAC address is in the valid-AP database on the switch or on the RADIUS server and the AP type is marked as Rogue, then the AP state - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 438
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide AP is operating on an illegal APs are classified as rogues before enabling the attack feature. This feature is disabled by default. Click the Apply button to accept the changes made. After clicking the Client Configuration tab - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 439
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Not Present in OUI Database Test Select remain authenticated with an unknown AP. Known Client Database Lookup Method Specify whether the Switch should use the Local or RADIUS database for the lookups in the Known Client - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 440
Clients DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Known Clients This window is used to display the wireless clients currently in the Known Client Database. To view this window, click Administration > Advanced Configuration > - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 441
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Switch Provisioning This window is used to configure switch provisioning. To view this window, click Administration > Advanced Configuration > Switch Provisioning as shown below: Figure 3-40 Switch Certificate Request window - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 442
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Switch IP Address Enter the IP address of the peer switch. Click the Start button to perform switch provisioning. 437 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 443
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 4 QoS Access Control Lists Differentiated Services Access Control Lists IP Access Control Lists IP access control lists (ACL) allow network managers to define classification actions and rules for wireless networks. To - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 444
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Parameter Description New IP ACL Name Enter a new name of IP ACL. Click the Apply button to accept the changes made. Click the Cancel button to discard the configuration. After clicking the Add / Delete Rules button - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 445
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide entered. Source IP Mask Enter the source IP mask. Click the Create Rule button to add a new rule. Click the Cancel button to discard the configuration. After clicking the Add Rule button to add a rule for Extended IP ACL, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 446
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide IP DSCP - Select one of the DSCP keyword values from the IP DSCP drop-down menu. When selecting Other, the IP DSCP Value field appears. Enter a value in the field. IP Precedence - Enter a value between 0 and 7 in the IP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 447
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide packet's TCP/UDP destination port. When selecting Other, Destination Port Value appears. Enter a value in the field. Service Type Select one of the following three Match conditions for the extended IP ACL rule. IP DSCP - - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 448
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 4-8 IP Access Control Lists - Edit Rule (Extended IP ACL) window The fields that can be configured are described below: Parameter Description Action Match Every Protocol Source IP Address Source IP Mask Source L4 Port - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 449
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Cancel button to discard the configuration. After clicking the Rule ID hyperlink or the Edit button to modify a rule for Named IP ACL, the following page appears: - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 450
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide extended IP ACL rule. IP DSCP - Select one of the DSCP keyword values from the IP DSCP drop-down menu. When selecting Other, the IP DSCP Value field appears. Enter a value in the field. IP Precedence - Enter a value between 0 and - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 451
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide After clicking the Add / Delete Rules button match criteria. Use the drop-down menu to select a packet's IP protocol to match condition for the selected IP ACL rule. When selecting Other, the Protocol Value field appears. Enter - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 452
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Source Prefix Enter an IPv6 prefix Enter a value of IPv6 flow label. IP DSCP Service Select one of the DSCP keyword values from the IP DSCP drop-down menu. When selecting Other, the IP DSCP Value field appears. Enter a value - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 453
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Source Prefix Tick the check box value of IPv6 flow label. IP DSCP Service Tick the check box and select one of the DSCP keyword values from the IP DSCP drop-down menu. When selecting Other, the IP DSCP Value field appears. - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 454
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 4-16 MAC Access Control Lists - Rename window The fields that can be configured are described below: Parameter Description New MAC ACL Name Enter a new - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 455
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide matches the rule's criteria. Match Every Use the drop-down menu to select True or False. True means that all packets will match the selected - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 456
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide CoS Tick the check box and enter the the Cancel button to discard the configuration. Differentiated Services The QoS feature contains Differentiated Services (DiffServ) support that allows traffic to be classified into streams - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 457
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 4-21 Class Configuration window The menu. Class of Service - Select this and select a value (between 0 and 7) of Class of Service in the next window. Destination IP Address - Select this to enter an IP address and its - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 458
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Any - All packets are considered to match the specified class and no additional input information is needed. IP DSCP - Select this to choose IP window. the packet's Type of Service bits in the IP header must match the entered - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 459
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 4-23 Policy Configuration window The fields that can be configured are described for that policy-class instance. To view this window, click QoS > Differentiated Services > Policy Class Definition as shown below: 454 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 460
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide . Use the drop-down menu to select attributes supported for this type of policy. Click the Configure Selected specified class of service value in the priority field of the 802.1p header in the next window. Mark IP DSCP - Select - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 461
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Mark CoS - The packets are marked by DiffServ with the specified CoS value before being presented to the system forwarding element. Enter a value in the Conform CoS Value field between 0 and 7. Mark IP DSCP - The packets are - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 462
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 5 Download Image Launch... Network Visualization on the WLAN Visualization graph, you can access information about the object and links to configuration pages on the Web interface. Download Image This window is used - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 463
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 5-2 D-Link WLAN Visualization window You can import multiple images to the right window and drag the switches, APs or clients on the left window to the right to create virtual wireless network environment. Menu Bar The D- - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 464
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide • Exit - Exit the WLAN Visualization application. Edit • New Graph... - Select to open a window to create and configure a . Help • Summary - A new window opens to display the on-line help of D-Link WLAN Visualization. 459 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 465
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Section 4 Save and Tools Save Configuration / Log Stacking Information Download firmware Upload Firmware Download Configuration Upload Configuration Upload Log File Reset Reboot System Chapter 1 Save Save Configuration / Log To - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 466
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Chapter 2 Tools License Management This window is used to install an activation code. The activation code is a set of codes which actives/unlocks function on - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 467
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-3 Download Firmware - HTTP window The fields that can be configured are described below: Parameter Description Destination File Enter the location of the Destination File. Source File Enter - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 468
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Download Configuration From TFTP This page allows the user to download the configuration file from a TFTP Server to the Switch and updates the switch. Figure 2-5 Download Configuration - TFTP window The fields that can be - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 469
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Upload Configuration To TFTP This page allows the user to upload the configuration file from the Switch or STP. Select the appropriate Filter action and enter the service name in the space provided. Click Upload to initiate the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 470
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Upload Log To TFTP This page allows the user to upload the log file from the Switch to a TFTP Server. Figure 2-9 Upload Log - TFTP window The fields that can be configured are described below: Parameter Description TFTP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 471
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide NOTE: Only the Reset System option will enter the factory default parameters into the Switch's nonvolatile RAM, and then restart the Switch. All other options enter the factory defaults into the current configuration, but do not - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 472
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 2-13 System Rebooting window 467 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 473
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Appendices IP and MAC information in the ARP packets to attack a LAN (known as ARP spoofing). This document is intended to introduce the ARP protocol, ARP spoofing attacks, and the countermeasures brought by D-Link's switches - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 474
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide When the switch receives the frame, it will check the "Source Address" in the Ethernet frame's header. If the address is not in its Forwarding Table, the switch will learn PC A's MAC and the associated port into its Forwarding - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 475
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide The switch will also examine the "Source Address" of the Ethernet frame and find that the address is not in the Forwarding Table. The switch IP address of another node (such as the default gateway). Any traffic meant for that IP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 476
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide A common DoS attack today can be done by associating a nonexistent or any specified MAC address to the IP address of the network's default ACL D-Link managed switches can supported per switch. In other words, up to - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 477
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Offset Offset Offset Offset second chunk starts from Chunk 7 mask for Sender IP in ARP packet. (Green in Table 6, 29th and 30th bytes) The third chunk starts from Chunk 8 mask for Sender IP in ARP packet. (Brown in Table 6, - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 478
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide 0xA5A offset_chunk_3 0x5A5A0000 Step 5: save Save configuration. 473 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 479
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Appendix B Password Recovery Procedure This document describes the procedure for resetting passwords on D-Link Switches command resets the whole configuration back to the default values. The option 'force_agree' means to reset - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 480
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Appendix C System Log Entries The following table lists all possible entries and their corresponding meanings that will appear in the System Log of this Switch Firmware upgraded by console successfully (Username: , IP: - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 481
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Firmware upgrade was unsuccessful Firmware upgrade by console was unsuccessful! (Username: , IP: ) Warning Configuration successfully downloaded Configuration successfully downloaded by console(Username: < - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 482
Interface Console Web TELNET DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Log message upload was unsuccessful Log message upload by console was unsuccessful! (Username: , IP: ) Warning Firmware successfully uploaded Firmware successfully uploaded by - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 483
SNMP STP DoS SSH AAA DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Login failed through TELNET Logout through The source IP is same as Switch's interface IP but the source MAC is different 2. Source IP is the same as the Switch's IP in ARP packet 3. Self IP packet detected - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 484
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Successful login through Web authenticated by AAA local method (Username: ) Warning Informational Warning Warning Informational Warning Warning Informational There are no IP and MAC if login by console. There are no - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 485
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Login failed through TELNET authenticated by AAA server Login failed through TELNET due to AAA server timeout or improper configuration Successful login through SSH authenticated - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 486
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide configuration Port Security MBAC IMPB Successful A host passes the authentication A host is aged out Unauthenticated IP address encountered and discarded by IP IP-MAC port binding Dynamic IMPB entry is conflict with static ARP - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 487
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide ) IP and Password Changed Dynamic IMPB entry is conflict with static FDB Dynamic IMPB entry conflicts with static IMPB Creating IMPB entry failed due to no ACL rule available IP Address change activity Dynamic IMPB - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 488
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide CFM CFM Extension Voice VLAN ERPS Temperature recovers Warning Command logging Wireless State Table Full Command Logging Wireless Switch enabled Wireless Switch disabled Wireless locally managed AP limit is exceeded Wireless - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 489
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide database full full client MAC: dropped Peer Switch Managed AP RF Scan Load Balacing Configuration Push WIDS Auto Channel & Power Captive Portal Wireless peer Switch discovered Wireless peer Switch failed Wireless - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 490
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide CP Client Auth Failure CP Client Authentication Database Full CP Client Auth Failure: MAC: IP: SwMAC: CPID: Interface: User: CP Client Authentication Database Full Warning - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 491
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Appendix D Trap Log Entries This table lists the trap logs found on the Switch server is detected. The same illegal DHCP server IP address detected is just sent once to the trap receivers within the log ceasing unauthorized duration - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 492
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide warmStart SNMP entity, acting in an agent role, has detected that the ifOperStatus object for one of its communication links is about to enter the down state from some other state (but not from the notPresent state). This - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 493
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide wsAPFailureListFull wsRFScanAPListFull wsClientAssociationDatabaseFull wsPeerSwitchDiscovered wsPeerSwitchFailed wsPeerSwitchUnknownProtocol wsManagedAPDiscovered wsManagedAPFailed wsManagedAPUnknownProtocol - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 494
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide trap signifies that the SNMP entity, acting in an agent role, has detected that the Peer Switch Managed AP database limit has exceeded. A wsClusterControllerElected trap signifies that the SNMP entity, acting in - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 495
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Appendix E RADIUS Attributes Assignment The RADIUS Attributes Assignment on the Switch Field Used to assign the 802.1p default priority of the port. Value Usage 171 (DLINK) Required 4 Required 0-7 Required If the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 496
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Tunnel-Type Tunnel-Medium-Type Tunnel-Private-Group : RADIUS Tunnel Attribute Description Vendor-ID Defines the vendor. Value 171 (DLINK) Usage Required Vendor-Type Defines the attribute. 12 (for ACL profile) 13 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 497
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Attribute-Specific Field Link (171), Location (101) Vendor-Specifc (26), D-Link (171), Mode (102) Vendor-Specifc (26), D-Link (171), Profile-ID (103) Vendor-Specifc (26), D-Link (171), Switch-IP (104) Vendor-Specifc (26), D-Link - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 498
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Radio-1-Power (107) Vendor-Specifc (26), D-Link (171), Radio-2-Power (108) Vendor-Specifc (26), D-Link (171), Expected-Channel (112) Vendor-Specifc (26), D-Link (171), Expected-AP-Security (110) Vendor-Specifc (26), D-Link (171 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 499
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Client-ACL-Up (121) Vendor-Specific (26), D-Link (171), Client-Policy-Dn (122) Vendor-Specific (26), D-Link then the Client QoS Default Policy Down parameter defined in client stations that do not support 802.1X. The following - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 500
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Tunnel- (14122), WISPr-Bandwidth-Max-Up (7) Vendor-Specific (26), D-Link (171), LVL7-Max-Input-Octets Description User name to be authorized Required Required Optional Default None None 86400 Optional 0 Optional 0 Optional - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 501
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide (124) Vendor-Specific (26), D-Link (171), LVL7-Max-Output-Octets (125) Vendor-Specific (26), D-Link (171), LVL7-Max-Total-Octets (126) Vendor-Specific (26), D-Link 0 0 None. The default group is used if not defined here. 496 - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 502
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Appendix F Wireless Switch cluster to support client authenticated roaming. Cluster Controller Election Each Switch in the another Switch. The Switch keeps a list of Cluster priorities and IP addresses for each peer Switch and - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 503
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Since the Cluster Controller function may be disabled by setting the Cluster Priority to zero, it is possible that all wireless Switches in the network are configured to disable the Cluster Controller function and the network - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 504
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Each wireless device has a copy of a Wireless feature is not disabled and service to the wireless clients is not interrupted. IP Tunnel versus MBA and IMPB When Wireless Switches enables IP tunneling for wireless clients, the - D-Link DWS-3160-24TC | DWS-3160 Series Web UI Reference Guide - Page 505
DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide In other words, MBA and IMPB will not work when the MAC belongs to a tunnel client. To achieve IP-in-IP tunnel forwarding, the MAC addresses of the devices under the tunnel are learned and marked as "static" FDB entries on the
Fdo