Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 252

CP Configuration, Security > Captive Portal CP > CP Configuration

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 252 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 11-67 Global Configuration window The fields that can be configured or displayed are described below: Parameter Description CP Global State Click the radio buttons to enable or disable the CP global state. CP Global Operational Status Display the status of the CP operational status. CP Global Disable Reason When captive portal is disabled, the field displays the reason being disabled. Available reasons are: Administrator Disabled, IP Address Not Configured, No IP Routing Interface and Routing Disabled. Additional HTTP Port (0-65535) Enter the additional HTTP port number between 0 and 65535, except 80 and 443. 80 is reserved for HTTP default port, and 443 is reserved for HTTPS default port. The default value is 0 which represents that no additional port is used, and the default port (80) is used. Additional HTTP Secure Port (0-65535) Enter the additional HTTPS port number between 0 and 65535, except 80 and 443. 80 is reserved for HTTP default port, and 443 is reserved for HTTPS default port. The default value is 0 which represents that no additional port is used, and the default port (443) is used. Peer Switch Statistics Reporting Interval (15-3600) When clustering is supported on the switch, enter an interval that the peer switches send its authenticated client statistics to the Cluster Controller periodically. The reporting interval is in the range of 0, 15-3600 seconds. The value 0 means the function is disabled. The default value is 120. Authentication Timeout (60-600) Enter a time for authentication. If a CP user does not enter valid credentials within the time, the authentication page needs to be served again in order for the client to gain access to the network. The value is between 60 and 600 seconds. Click the Apply button to accept the changes made for each individual section. CP Configuration This window is used to create CP configuration. To view this window, click Security > Captive Portal (CP) > CP Configuration as shown below: 247

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

247

Figure 11-67 Global Configuration window

The fields that can be configured or displayed are described below:

Parameter

Description

CP Global State

Click the radio buttons to enable or disable the CP global state.

CP Global

Operational Status

Display the status of the CP operational status.

CP Global Disable

Reason

When captive portal is disabled, the field displays the reason being disabled.

Available reasons are:

Administrator Disabled

IP Address Not Configured

No IP

Routing Interface

and

Routing Disabled

Additional HTTP Port

(0-65535)

Enter the additional HTTP port number between 0 and 65535, except 80 and 443. 80

is reserved for HTTP default port, and 443 is reserved for HTTPS default port. The

default value is 0 which represents that no additional port is used, and the default port

(80) is used.

Additional HTTP

Secure Port (0-65535)

Enter the additional HTTPS port number between 0 and 65535, except 80 and 443.

80 is reserved for HTTP default port, and 443 is reserved for HTTPS default port. The

default value is 0 which represents that no additional port is used, and the default port

(443) is used.

Peer Switch Statistics

Reporting Interval

(15-3600)

When clustering is supported on the switch, enter an interval that the peer switches

send its authenticated client statistics to the Cluster Controller periodically. The

reporting interval is in the range of 0, 15-3600 seconds. The value 0 means the

function is disabled. The default value is 120.

Authentication

Timeout (60-600)

Enter a time for authentication. If a CP user does not enter valid credentials within the

time, the authentication page needs to be served again in order for the client to gain

access to the network. The value is between 60 and 600 seconds.

Click the

Apply

button to accept the changes made for each individual section.

CP Configuration

This window is used to create CP configuration.

To view this window, click

Security > Captive Portal (CP) > CP Configuration

as shown below: