Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 14

Port Description Settings, Flow Control, Address Learning, Medium Type, Apply, Refresh, System

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide from a data stream received from the master. If one connection is set for 1000M Full_Master, the other side of the connection must be set for 1000M Full_Slave. Any other configuration will result in a link down status for both ports. Flow Control Displays the flow control scheme used for the various port configurations. Ports configured for full-duplex use 802.3x flow control, half-duplex ports use backpressure flow control, and Auto ports use an automatic selection of the two. The default is Disabled. Address Learning Enable or disable MAC address learning for the selected ports. When Enabled, destination and source MAC addresses are automatically listed in the forwarding table. When address learning is Disabled, MAC addresses must be manually entered into the forwarding table. This is sometimes done for reasons of security or efficiency. See the section on Forwarding/Filtering for information on entering MAC addresses into the forwarding table. The default setting is Enabled. MDIX Auto - Select auto for auto sensing of the optimal type of cabling. Normal - Select normal for normal cabling. If set to normal state, the port is in MDI mode and can be connected to a PC NIC using a straight-through cable or a port (in MDI mode) on another switch through a cross-over cable. Cross - Select cross for cross cabling. If set to cross state, the port is in MDIX mode, and can be connected to a port (in MDI mode) on another switch through a straight cable. Medium Type If configuring the Combo ports, this defines the type of transport medium to be used. Click the Apply button to implement changes made. Click the Refresh button to refresh the display section of this page. Port Description Settings The Switch supports a port description feature where the user may name various ports. To view the following window, click System Configuration > Port Configuration > Port Description Settings, as show below: Figure 5-4 Port Description Settings window 9

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

from a data stream received from the master. If one connection is set for

1000M

Full_Master

, the other side of the connection must be set for

1000M Full_Slave

. Any

other configuration will result in a link down status for both ports.

Flow Control

Displays the flow control scheme used for the various port configurations. Ports

configured for full-duplex use 802.3x flow control, half-duplex ports use backpressure

flow control, and Auto ports use an automatic selection of the two. The default is

Disabled

Address Learning

Enable or disable MAC address learning for the selected ports. When

Enabled

destination and source MAC addresses are automatically listed in the forwarding table.

When address learning is

Disabled

, MAC addresses must be manually entered into the

forwarding table. This is sometimes done for reasons of security or efficiency. See the

section on Forwarding/Filtering for information on entering MAC addresses into the

forwarding table. The default setting is

Enabled

MDIX

Auto

- Select auto for auto sensing of the optimal type of cabling.

Normal

- Select normal for normal cabling. If set to normal state, the port is in MDI mode

and can be connected to a PC NIC using a straight-through cable or a port (in MDI

mode) on another switch through a cross-over cable.

Cross

- Select cross for cross cabling. If set to cross state, the port is in MDIX mode, and

can be connected to a port (in MDI mode) on another switch through a straight cable.

Medium Type

If configuring the Combo ports, this defines the type of transport medium to be used.

Click

the

Apply

button to implement changes made.

Click the

Refresh

button to refresh the display section of this page.

Port Description Settings

The Switch supports a port description feature where the user may name various ports.

To view the following window, click

System

Configuration > Port Configuration > Port Description Settings

, as

show below:

Figure 5-4 Port Description Settings window