Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 500

Captive Portal RADIUS Attributes, For dynamic VLAN

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 500 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Tunnel-Type (64) Tunnel-Medium-Type (65) Tunnel-Private-Group-ID (81) For dynamic VLAN usage. For dynamic VLAN usage. For dynamic VLAN usage. VLAN (13) 802 VLANID Optional Optional Optional If the global MAC Authentication action is configured as "White List", then any wireless clients with MAC addresses that are specified in the list, and are not explicitly denied access, are granted access. If MAC address is not in the list, then the access to the client is denied. If the global MAC Authentication action is configured as "Black List", then any wireless clients with MAC addresses that are specified in the list, and are not explicitly granted access, are denied access. If MAC address is not in the list, then the access to the client is granted. Captive Portal RADIUS Attributes The following table indicates the RADIUS attributes that are used to configure Captive Portal users. The table indicates both RADIUS attributes and vendor specific attributes (VSA) that are used to configure Captive Portal. Attribute User-Name (1) User-Password (2) Session-Timeout (27) Idle-Timeout (28) Vendor-Specific (26), WISPr (14122), WISPr-Bandwidth-MaxDown (8) Vendor-Specific (26), WISPr (14122), WISPr-Bandwidth-Max-Up (7) Vendor-Specific (26), D-Link (171), LVL7-Max-Input-Octets Description User name to be authorized User password Logout once session timeout is reached (seconds). If the attribute is 0 or not present, then use the value configured for the Captive Portal. Logout once idle timeout is reached (seconds). If the attribute is 0 or not present, then use the value configured for the Captive Portal. Maximum client receive rate (b/s). Limits the bandwidth at which the client can receive data from the network. If the attribute is 0 or not present, then use the value configured for the Captive Portal. Maximum client transmit rate (b/s). Limits the bandwidth at which the client can send data into the network. If the attribute is 0 or not present, then use the value configured for the Captive Portal. Maximum number of octets the user is allowed to transmit. After this limit Range 1-32 characters 8-64 characters Integer (seconds) Integer (seconds) Integer Integer Integer Usage Required Required Optional Default None None 86400 Optional 0 Optional 0 Optional 0 Optional 0 495

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

495

Tunnel-Type (64)

For dynamic VLAN

usage.

VLAN (13)

Optional

Tunnel-Medium-Type (65)

For dynamic VLAN

usage.

802

Optional

Tunnel-Private-Group-ID

(81)

For dynamic VLAN

usage.

VLANID

Optional

If the global MAC Authentication action is configured as “White List”, then any wireless clients with MAC addresses

that are specified in the list, and are not explicitly denied access, are granted access. If MAC address is not in the

list, then the access to the client is denied.

If the global MAC Authentication action is configured as “Black List”, then any wireless clients with MAC addresses

that are specified in the list, and are not explicitly granted access, are denied access. If MAC address is not in the

list, then the access to the client is granted.

The following table indicates the RADIUS attributes that are used to configure Captive Portal users. The table

indicates both RADIUS attributes and vendor specific attributes (VSA) that are used to configure Captive Portal.

Captive Portal RADIUS Attributes

Attribute

Description

Range

Usage

Default

User-Name (1)

User name to be

authorized

1-32 characters

Required

None

User-Password (2)

User password

8-64 characters

Required

None

Session-Timeout (27)

Logout once session

timeout is reached

(seconds). If the attribute

is 0 or not present, then

use the value configured

for the Captive Portal.

Integer (seconds)

Optional

86400

Idle-Timeout (28)

Logout once idle timeout

is reached (seconds). If

the attribute is 0 or not

present, then use the

value configured for the

Captive Portal.

Integer (seconds)

Optional

Vendor-Specific (26),

WISPr (14122),

WISPr-Bandwidth-Max-

Down (8)

Maximum client receive

rate (b/s). Limits the

bandwidth at which the

client can receive data

from the network. If the

attribute is 0 or not

present, then use the

value configured for the

Captive Portal.

Integer

Optional

Vendor-Specific (26),

WISPr (14122),

WISPr-Bandwidth-Max-Up

(7)

Maximum client transmit

rate (b/s). Limits the

bandwidth at which the

client can send data into

the network. If the

attribute is 0 or not

present, then use the

value configured for the

Captive Portal.

Integer

Optional

Vendor-Specific (26),

D-Link (171),

LVL7-Max-Input-Octets

Maximum number of

octets the user is allowed

to transmit. After this limit

Integer

Optional