Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 319

Enable Captive Portal, Max Up Rate

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 319 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide After clicking the link or the tab, the following page will appear: Figure 1-3 CP Configuration - Edit window The fields that can be configured are described below: Parameter Description Enable Captive Portal Configuration Name Protocol Mode Verification Mode User Logout Mode Redirect Mode Redirect URL Idle Time Session Timeout Max Up Rate Max Down Rate Max Receive Click the radio buttons to enable or disable the CP configuration. Enter to modify the configuration name. Click the radio buttons to use HTTP or HTTPS as the protocol that CP configuration is used during verification process. Click the radio buttons to select the verification mode for the CP to verify clients. • Guest - The user does not need to be authenticated by a database. • Local - The Switch uses a local database to authenticate users. • RADIUS - The Switch uses a database on a remote RADIUS server to authenticate users. Click the radio buttons to enable or disable the ability for an authenticated user to deauthenticate from the network. Click the radio buttons to enable or disable the redirect mode for a CP configuration. When the Redirect Mode is enabled, enter the URL to which the newly authenticated client is redirected. Enter the idle time in seconds to allow a user remain idle before automatically being logged out. The value 0 indicates that the timeout is not enforced. The default value is 0. Enter the waiting time in seconds before terminating a session. A user is logged out once the session timeout is reached. The value 0 indicates that the timeout is not enforced. Enter the maximum rate, in bytes per second, that a client can transmit data into the network when using the captive portal. The rate is between 0 and 536870911. Enter the maximum rate, in bytes per second, that a client can receive data from the network when using the captive portal. The rate is between 0 and 536870911. Enter the maximum number of bytes that a client is allowed to receive when using the captive portal. After this limit has been reached the user will be disconnected. 314

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

314

After clicking the link or the tab, the following page will appear:

Figure 1-3 CP Configuration - Edit window

The fields that can be configured are described below:

Parameter

Description

Enable Captive Portal

Click the radio buttons to enable or disable the CP configuration.

Configuration Name

Enter to modify the configuration name.

Protocol Mode

Click the radio buttons to use HTTP or HTTPS as the protocol that CP configuration is

used during verification process.

Verification Mode

Click the radio buttons to select the verification mode for the CP to verify clients.

•

Guest

– The user does not need to be authenticated by a database.

•

Local

– The Switch uses a local database to authenticate users.

•

RADIUS

– The Switch uses a database on a remote RADIUS server to

authenticate users.

User Logout Mode

Click the radio buttons to enable or disable the ability for an authenticated user to de-

authenticate from the network.

Redirect Mode

Click the radio buttons to enable or disable the redirect mode for a CP configuration.

Redirect URL

When the Redirect Mode is enabled, enter the URL to which the newly authenticated

client is redirected.

Idle Time

Enter the idle time in seconds to allow a user remain idle before automatically being

logged out. The value 0 indicates that the timeout is not enforced. The default value is

Session Timeout

Enter the waiting time in seconds before terminating a session. A user is logged out

once the session timeout is reached. The value 0 indicates that the timeout is not

enforced.

Max Up Rate

Enter the maximum rate, in bytes per second, that a client can transmit data into the

network when using the captive portal. The rate is between 0 and 536870911.

Max Down Rate

Enter the maximum rate, in bytes per second, that a client can receive data from the

network when using the captive portal. The rate is between 0 and 536870911.

Max Receive

Enter the maximum number of bytes that a client is allowed to receive when using the

captive portal. After this limit has been reached the user will be disconnected.