Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 134

VRRP Global Settings, VRRP Virtual Router Settings

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide VRRP Global Settings This window is used to configure the VRRP Global settings. To view the following window, click L3 Features > VRRP > VRRP Global Settings, as show below: Figure 8-5 VRRP Global Settings window The fields that can be configured are described below: Parameter Description VRRP State Use the drop-down menu to enable or disable the VRRP state. Non-owner response Ping Specify that the virtual IP address is allowed to be pinged from other host end nodes to verify connectivity. Click the Apply button to accept the changes made. VRRP Virtual Router Settings This window is used to configure VRRP virtual router settings. To view the following window, click L3 Features > VRRP > VRRP Virtual Router Settings, as show below: Figure 8-6 VRRP Virtual Router Settings window The fields that can be configured are described below: Parameter Description Interface Name VRID (1-255) IP Address State Priority (1-254) Advertisement Enter the IP interface name used to create a VRRP entry. Enter the ID of the virtual router. All the routers participating in this group must be assigned the same VRID value. This value must be different from other VRRP groups set on the Switch. Enter the virtual router's IP address. This IP address is also the default gateway that will be statically assigned to end hosts and must be set for all routers that participate in this group. Use the drop-down menu to enable or disable the state of the virtual router function of the interface. Enter the priority to be used for the Virtual Router Master election process. The VRRP Priority value may determine if a higher priority VRRP router overrides a lower priority VRRP router. A higher priority increases the possibility to become the Master router of the group. A lower priority increases the possibility to become the backup router. For VRRP routers with the same priority value, the VRRP router with the highest physical IP address is chosen to be the Master router. Enter the interval between sending advertisement messages. 129

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

129

VRRP Global Settings

This window is used to configure the VRRP Global settings.

To view the following window, click

L3 Features > VRRP > VRRP Global Settings

, as show below:

Figure 8-5 VRRP Global Settings window

The fields that can be configured are described below:

Parameter

Description

VRRP State

Use the drop-down menu to enable or disable the VRRP state.

Non-owner

response Ping

Specify that the virtual IP address is allowed to be pinged from other host end nodes to

verify connectivity.

Click the

Apply

button to accept the changes made.

VRRP Virtual Router Settings

This window is used to configure VRRP virtual router settings.

To view the following window, click

L3 Features > VRRP > VRRP Virtual Router Settings

, as show below:

Figure 8-6 VRRP Virtual Router Settings window

The fields that can be configured are described below:

Parameter

Description

Interface Name

Enter the IP interface name used to create a VRRP entry.

VRID (1-255)

Enter the ID of the virtual router. All the routers participating in this group must be

assigned the same VRID value. This value must be different from other VRRP groups

set on the Switch.

IP Address

Enter the virtual router’s IP address. This IP address is also the default gateway that

will be statically assigned to end hosts and must be set for all routers that participate in

this group.

State

Use the drop-down menu to enable or disable the state of the virtual router function of

the interface.

Priority (1-254)

Enter the priority to be used for the Virtual Router Master election process. The VRRP

Priority value may determine if a higher priority VRRP router overrides a lower priority

VRRP router. A higher priority increases the possibility to become the Master router of

the group. A lower priority increases the possibility to become the backup router. For

VRRP routers with the same priority value, the VRRP router with the highest physical

IP address is chosen to be the Master router.

Enter the interval between sending advertisement messages.