Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 495

Appendix E RADIUS Attributes Assignment

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 495 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Appendix E RADIUS Attributes Assignment The RADIUS Attributes Assignment on the Switch is used in the following modules: 802.1X (Port-based and Hostbased), MAC-based Access Control, and Captive Portal Configurations. The description that follows explains the following RADIUS Attributes Assignment types: • Ingress/Egress Bandwidth • 802.1p Default Priority • VLAN • ACL To assign Ingress/Egress bandwidth by RADIUS Server, the proper parameters should be configured on the RADIUS Server. The tables below show the parameters for bandwidth. The parameters of the Vendor-Specific attributes are: Vendor-Specific Attribute Description Vendor-ID Defines the vendor. Vendor-Type Defines the attribute. Attribute-Specific Field Used to assign the bandwidth of a port. Value 171 (DLINK) 2 (for ingress bandwidth) 3 (for egress bandwidth) Unit (Kbits) Usage Required Required Required If the user has configured the bandwidth attribute of the RADIUS server (for example, ingress bandwidth 1000Kbps) and the 802.1X authentication is successful, the device will assign the bandwidth (according to the RADIUS server) to the port. However, if the user does not configure the bandwidth attribute and authenticates successfully, the device will not assign any bandwidth to the port. If the bandwidth attribute is configured on the RADIUS server with a value of "0" or more, than the effective bandwidth (100Mbps on an Ethernet port or 1Gbps on a Gigabit port) of the port will be set to no_limited. To assign 802.1p default priority by RADIUS Server, the proper parameters should be configured on the RADIUS Server. The tables below show the parameters for 802.1p default priority. The parameters of the Vendor-Specific attributes are: Vendor-Specific Attribute Description Vendor-ID Defines the vendor. Vendor-Type Defines the attribute. Attribute-Specific Field Used to assign the 802.1p default priority of the port. Value Usage 171 (DLINK) Required 4 Required 0-7 Required If the user has configured the 802.1p priority attribute of the RADIUS server (for example, priority 7) and the 802.1X, or Host-based authentication is successful, the device will assign the 802.1p default priority (according to the RADIUS server) to the port. However, if the user does not configure the priority attribute and authenticates successfully, the device will not assign a priority to this port. If the priority attribute is configured on the RADIUS server is a value out of range (>7), it will not be set to the device. To assign VLAN by RADIUS Server, the proper parameters should be configured on the RADIUS Server. To use VLAN assignment, RFC3580 defines the following tunnel attributes in RADIUS packets. The table below shows the parameters for a VLAN: RADIUS Tunnel Attribute Description Value Usage 490

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

490

Appendix E RADIUS Attributes Assignment

The RADIUS Attributes Assignment on the Switch is used in the following modules: 802.1X (Port-based and Host-

based), MAC-based Access Control, and Captive Portal Configurations.

The description that follows explains the following RADIUS Attributes Assignment types:

•

Ingress/Egress Bandwidth

•

802.1p Default Priority

•

VLAN

•

ACL

To assign

Ingress/Egress bandwidth by RADIUS Server

, the proper parameters should be configured on the

RADIUS Server. The tables below show the parameters for bandwidth.

The parameters of the Vendor-Specific attributes are:

Vendor-Specific Attribute

Description

Value

Usage

Vendor-ID

Defines the vendor.

171 (DLINK)

Required

Vendor-Type

Defines the attribute.

2 (for ingress bandwidth)

3 (for egress bandwidth)

Required

Attribute-Specific Field

Used to assign the bandwidth of a

port.

Unit (Kbits)

Required

If the user has configured the bandwidth attribute of the RADIUS server (for example, ingress bandwidth 1000Kbps)

and the 802.1X authentication is successful, the device will assign the bandwidth (according to the RADIUS server)

to the port. However, if the user does not configure the bandwidth attribute and authenticates successfully, the

device will not assign any bandwidth to the port. If the bandwidth attribute is configured on the RADIUS server with

a value of “0” or more, than the effective bandwidth (100Mbps on an Ethernet port or 1Gbps on a Gigabit port) of

the port will be set to no_limited.

To assign

802.1p default priority by RADIUS Server

, the proper parameters should be configured on the

RADIUS Server. The tables below show the parameters for 802.1p default priority.

The parameters of the Vendor-Specific attributes are:

Vendor-Specific Attribute

Description

Value

Usage

Vendor-ID

Defines the vendor.

171 (DLINK) Required

Vendor-Type

Defines the attribute.

Required

Attribute-Specific Field

Used to assign the 802.1p default priority of the port.

0-7

Required

If the user has configured the 802.1p priority attribute of the RADIUS server (for example, priority 7) and the 802.1X,

or Host-based authentication is successful, the device will assign the 802.1p default priority (according to the

RADIUS server) to the port. However, if the user does not configure the priority attribute and authenticates

successfully, the device will not assign a priority to this port. If the priority attribute is configured on the RADIUS

server is a value out of range (>7), it will not be set to the device.

To assign

VLAN by RADIUS Server

, the proper parameters should be configured on the RADIUS Server. To use

VLAN assignment, RFC3580 defines the following tunnel attributes in RADIUS packets.

The table below shows the parameters for a VLAN:

RADIUS Tunnel Attribute

Description

Value

Usage