Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 458

Policy Configuration, IP DSCP Keyword, Precedence Value, Add Match Criteria, Apply, Cancel

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 458 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Any - All packets are considered to match the specified class and no additional input information is needed. IP DSCP - Select this to choose IP DSCP Keyword in the next window. The packet's DSCP must match the selected keyword. IP Precedence - Select this to choose Precedence Value in the next window. The packet's DSCP must match the selected value. IP TOS - Select this to enter the ToS bits and its mask in the next window. the packet's Type of Service bits in the IP header must match the entered value. Protocol - Select this to choose a protocol in the next window. A packet's layer 4 protocol must match the selected protocol. Reference Class - Select to choose a class to start referencing for criteria in the next window. Source IP Address - Select to enter an IP address and its mask in the next window. A packet's source IP address must match the entered IP address and its mask. Source Layer4 Port - Select this to choose protocol keyword in the next window. A packet's TCP/UDP source port must match the selected port. Source MAC Address - Select this to enter a MAC address and its mask in the next window. A packet's source MAC address must match the address entered. VLAN - Select this to enter a VLAN ID in the next window. When Class Layer 3 Protocol is IPv6, the following selections display in the dropdown menu. Destination IPv6 Address - Select this to enter an IPv6 prefix and its length in the next window. A packet's destination IPv6 prefix must match the address entered. Destination Layer4 Port - Select this to choose protocol keyword in the next window. A packet's TCP/UDP destination port must match the selected port. Any - All packets are considered to match the specified class and no additional input information is needed. Flow Label - Select this to enter the flow label value in the next window. IP DSCP - Select this to choose IP DSCP Keyword in the next window. The packet's DSCP must match the selected keyword. Protocol - Select this to choose a protocol in the next window. A packet's layer 4 protocol must match the selected protocol. Reference Class - Select to choose a class to start referencing for criteria in the next window. Source IPv6 Address - Select this to enter an IPv6 prefix and its length in the next window. A packet's source port IPv6 prefix must match the address entered. Source Layer4 Port - Select this to choose protocol keyword in the next window. A packet's TCP/UDP source port must match the selected port. Click the Add Match Criteria to see the criteria configuration for the class. Click the Apply button to accept the changes made. Click the Cancel button to discard the configuration. Policy Configuration This window is used to associate a collection of classes with one or more policy statements. To view this window, click QoS > Differentiated Services > Policy Configuration as shown below: 453

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

453

Any

– All packets are considered to match the specified class and no additional

input information is needed.

IP DSCP

– Select this to choose

IP DSCP Keyword

in the next window. The

packet’s DSCP must match the selected keyword.

IP Precedence

– Select this to choose

Precedence Value

in the next window. The

packet’s DSCP must match the selected value.

IP TOS

– Select this to enter the ToS bits and its mask in the next window. the

packet’s Type of Service bits in the IP header must match the entered value.

Protocol

- Select this to choose a protocol in the next window. A packet’s layer 4

protocol must match the selected protocol.

Reference Class

– Select to choose a class to start referencing for criteria in the

next window.

Source IP Address

– Select to enter an IP address and its mask in the next

window. A packet’s source IP address must match the entered IP address and its

mask.

Source Layer4 Port

– Select this to choose protocol keyword in the next window. A

packet’s TCP/UDP source port must match the selected port.

Source MAC Address

– Select this to enter a MAC address and its mask in the

next window. A packet’s source MAC address must match the address entered.

VLAN

– Select this to enter a VLAN ID in the next window.

When Class Layer 3 Protocol is

IPv6

, the following selections display in the drop-

down menu.

Destination IPv6 Address

– Select this to enter an IPv6 prefix and its length in the

next window. A packet’s destination IPv6 prefix must match the address entered.

Destination Layer4 Port

– Select this to choose protocol keyword in the next

window. A packet’s TCP/UDP destination port must match the selected port.

Any

– All packets are considered to match the specified class and no additional

input information is needed.

Flow Label

– Select this to enter the flow label value in the next window.

IP DSCP

– Select this to choose

IP DSCP Keyword

in the next window. The

packet’s DSCP must match the selected keyword.

Protocol

– Select this to choose a protocol in the next window. A packet’s layer 4

protocol must match the selected protocol.

Reference Class

– Select to choose a class to start referencing for criteria in the

next window.

Source IPv6 Address

– Select this to enter an IPv6 prefix and its length in the next

window. A packet’s source port IPv6 prefix must match the address entered.

Source Layer4 Port

– Select this to choose protocol keyword in the next window. A

packet’s TCP/UDP source port must match the selected port.

Click the

Add Match Criteria

to see the criteria configuration for the class.

Click the

Apply

button to accept the changes made.

Click the

Cancel

button to discard the configuration.

Policy Configuration

This window is used to associate a collection of classes with one or more policy statements.

To view this window, click

QoS > Differentiated Services > Policy Configuration

as shown below: