Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 93

Forbidden Router Port, Static Router Port

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Fast Leave Enable or disable the IGMP snooping fast leave function. If enabled, the membership is immediately removed when the system receive the IGMP leave message. State If the state is enable, it allows the switch to be selected as a IGMP Querier (sends IGMP query packets). It the state is disabled, then the switch can not play the role as a querier. NOTE: that if the Layer 3 router connected to the switch provides only the IGMP proxy function but does not provide the multicast routing function, then this state must be configured as disabled. Otherwise, if the Layer 3 router is not selected as the querier, it will not send the IGMP query packet. Since it will not also send the multicast-routing protocol packet, the port will be timed out as a router port. Report Suppression When enabled, multiple IGMP reports or leave for a specific (S, G) will be integrated into one report only before sending to the router port. Data Driven Learning State Specify to enable or disable the data driven learning state. Data Drive Learning Aged Out Specify to enable or disable the data drive learning aged out option. Version Specify the version of IGMP packet that will be sent by this port. If an IGMP packet received by the interface has a version higher than the specified version, this packet will be dropped. Click the Apply button to accept the changes made. Click the

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

Fast Leave

Enable or disable the IGMP snooping fast leave function. If enabled, the

membership is immediately removed when the system receive the IGMP leave

message.

State

If the state is enable, it allows the switch to be selected as a IGMP Querier (sends

IGMP query packets). It the state is disabled, then the switch can not play the role

as a querier.

NOTE:

that if the Layer 3 router connected to the switch provides only the IGMP

proxy function but does not provide the multicast routing function, then this

state must be configured as disabled. Otherwise, if the Layer 3 router is not

selected as the querier, it will not send the IGMP query packet. Since it will

not also send the multicast-routing protocol packet, the port will be timed out

as a router port.

Report Suppression

When enabled, multiple IGMP reports or leave for a specific (S, G) will be

integrated into one report only before sending to the router port.

Data Driven Learning

State

Specify to enable or disable the data driven learning state.

Data Drive Learning

Aged Out

Specify to enable or disable the data drive learning aged out option.

Version

Specify the version of IGMP packet that will be sent by this port. If an IGMP packet

received by the interface has a version higher than the specified version, this

packet will be dropped.

Click the

Apply

button to accept the changes made.

Click the

<<Back

button to discard the changes made and return to the previous window.

After clicking the

Modify Router Port

link, the following page will appear:

Figure 7-44 IGMP Snooping Router Port Settings window

The fields that can be configured are described below:

Parameter

Description

Static Router Port

This section is used to designate a range of ports as being connected to multicast-

enabled routers. This will ensure that all packets with such a router as its destination

will reach the multicast-enabled router regardless of the protocol.

Forbidden Router Port

This section is used to designate a range of ports as being not connected to

multicast-enabled routers. This ensures that the forbidden router port will not

propagate routing packets out.

Dynamic Router Port

Displays router ports that have been dynamically configured.

Ports

Select the appropriate ports individually to include them in the Router Port

configuration.

Click the

Select All

button to select all the ports for configuration.