Dell W-Series 304 Instant 6.5.1.0-4.3.1.0 CLI Reference Guide - Page 938

Usage Guidelines This command displays details for all active APs on the controller. If an AP on your network does not appear in this table, it may have been classified as an inactive AP for any of the following reasons: l The AP is configured with a missing or incorrect VLAN. (For example, the AP is configured to use a tunneled SSID of VLAN 2 but the controller doesn't have a VLAN 2.) l The AP has an unknown AP group. l The AP has a duplicate AP name. l An AP with an external antenna is not provisioned with external antenna gain settings. l Both radios on the AP are disabled. l No virtual APs are defined on the AP. l The AP has profile errors. Issue the command "show profile errors" for details. l The GRE tunnel between the AP and the controller was blocked by a firewall after the AP became active. l The AP is temporarily down while it is upgrading its software. The AP will become active after upgrading. l An AP has conflicting configuration settings. For example, if the AP system profile on a single radio dual- band AP configures the radio uses 802.11g, but the virtual AP profile on the AP is set to use 802.11a, the AP might not appear to be active. Example The output of the command in the example below shows that the controller sees an active AP. In this example, the output has been divided into multiple sections to better fit on the pages of this document. In the actual command-line interface, it will appear in a single, long table. (host)# show ap active Active AP Table Name Group IP Address 11g Clients 11g Ch/EIRP/MaxEIRP 11a Clients 11a Ch/EIRP/MaxEIRP AP205 AP205 172.16.0.5 0 AP:HT:1+/6/20 0 AP:VHT:40E/18/21 AP325 AP325 172.16.0.4 0 AP:HT:7+/6/21.5 0 AP:VHT:157E/18/21 AP115 Ap115 172.16.0.6 0 AP:HT:11-/9/25.5 0 AP:HT:48-/18/19 AP335 AP335 172.16.0.3 0 AP:HT:1+/6/21.5 0 AP:VHT:149E+36E/18/21.5 AP315 AP315 172.16.0.7 0 AP:HT:7+/6/21.5 0 AP:VHT:40E/15/21 AP Type Flags Uptime Outer IP -------- 205 2a 6h:41m:53s N/A 325 A2a 6h:48m:5s N/A 115 2a 6h:46m:5s N/A 335 A2a 6h:52m:57s N/A 315 2a 6h:51m:20s N/A Flags: 1 = 802.1X authenticated AP; 2 = Using IKE version 2; A = Enet1 in active/standby mode; B = Battery Boost On; C = Cellular; D = Disconn. Extra Calls On; E = Wired AP enabled; F = AP failed 802.1X authentication; H = Hotspot Enabled; K = 802.11K Enabled; L = Client Balancing Enabled; M = Mesh; N = 802.11b protection disabled; P = PPPOE; R = Remote AP; S = AP connected as standby; X = Maintenance Mode; a = Reduce ARP packets in the air; d = Drop Mcast/Bcast On; u = Custom-Cert RAP; i = Provisioned as Indoor; o = Provisioned as Outdoor; r = 802.11r Enabled Q = DFS CAC timer running E = 80 MHz Channel Width +/- = 40 MHz Channel Width S = 160 MHz Channel Width E+E = 80 + 80 MHz Channel Width (i.e. 36E+149E) The output of this command includes the following information: 938| show ap active Dell Networking W-Series ArubaOS 6.5.x | Reference Guide