IBM 4846-545 Service Guide - Page 57

Display, tablet, cable, removing, replacing

Page 57 highlights

Removing and replacing FRUs Display tablet cable - removing and replacing 1. Switch OFF the power to the SurePOS 500. Unplug the power cord from the external power source. 2. Remove the tablet as described in "Display tablet - removing and replacing" on page 34. 3. Disconnect the display cable from the rear of the tablet by pressing on either side of the connector. 4. Remove the front cover as described "Front (or HDD) cover removal" on page 29. 5. Remove the speaker, if present. See "Speaker - removing and replacing" on page 62. 6. Remove the rear cover as described in "Rear cover removal" on page 30. 7. Remove the power supply as described in "Power supply - removing and replacing" on page 45. Figure 14. Removing the display tablet cable from the system board 8. Remove the clamps on front of the frame and hinge. 9. Disconnect the display tablet cable from the system board by loosening the two thumbscrews (see Figure 14). 10. Remove the base plate. See "Base plate - removing and replacing" on page 57. 11. Pull the cable free from the plastic guide in the frame. 12. To replace, reverse these procedures. Chapter 3. Removing and replacing FRUs for the SurePOS 500 Models 545 and 565 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196

Display
tablet
cable
removing
and
replacing
1.
Switch
OFF
the
power
to
the
SurePOS
500.
Unplug
the
power
cord
from
the
external
power
source.
2.
Remove
the
tablet
as
described
in
“Display
tablet
-
removing
and
replacing”
on
page
34.
3.
Disconnect
the
display
cable
from
the
rear
of
the
tablet
by
pressing
on
either
side
of
the
connector.
4.
Remove
the
front
cover
as
described
“Front
(or
HDD)
cover
removal”
on
page
29.
5.
Remove
the
speaker,
if
present.
See
“Speaker
removing
and
replacing”
on
page
62.
6.
Remove
the
rear
cover
as
described
in
“Rear
cover
removal”
on
page
30.
7.
Remove
the
power
supply
as
described
in
“Power
supply
removing
and
replacing”
on
page
45.
8.
Remove
the
clamps
on
front
of
the
frame
and
hinge.
9.
Disconnect
the
display
tablet
cable
from
the
system
board
by
loosening
the
two
thumbscrews
(see
Figure
14).
10.
Remove
the
base
plate.
See
“Base
plate
removing
and
replacing”
on
page
57.
11.
Pull
the
cable
free
from
the
plastic
guide
in
the
frame.
12.
To
replace,
reverse
these
procedures.
Figure
14.
Removing
the
display
tablet
cable
from
the
system
board
Removing
and
replacing
FRUs
Chapter
3.
Removing
and
replacing
FRUs
for
the
SurePOS
500
Models
545
and
565
35